- 您现在的位置：买卖IC网 > PDF目录20400 > DC1663A (Linear Technology)DEMO BOARD LTM4628 PDF资料下载
参数资料
| 型号： | DC1663A |
| 厂商： | Linear Technology |
| 文件页数： | 18/36页 |
| 文件大小： | 0K |
| 描述： | DEMO BOARD LTM4628 |
| 软件下载： | LTM4628 Spice Model |
| 设计资源： | LTM4628 Gerber Files DC1663A Design Files |
| 标准包装： | 1 |
| 系列： | µModule® |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 2，非隔离 |
| 输出电压： | 1.2V，1.5V |
| 电流 - 输出： | 8A，8A |
| 输入电压： | 4.5 ~ 26.5 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 400kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | LTM4628 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTM4628
APPLICATIONS INFORMATION
? V D ?
I D = I S ? e ? ?
V D = η ? V T ? ln D
V T =
INTV CC andEXTV CC
The LTM4628 module has an internal 5V low dropout
regulator that is derived from the input voltage. This
regulator is used to power the control circuitry and the
power MOSFET drivers. This regulator can source up to
70mA, and typically uses ~30mA for powering the device
at the maximum frequency.
EXTV CC allows an external 5V supply to power the LTM4628
and reduce power dissipation from the internal low dropout
5V regulator. The power loss savings can be calculated by:
(V IN – 5V) ? 30mA = P LOSS
EXTV CC has a threshold of 4.7V for activation, and a maxi-
mum rating of 6V. When using a 5V input, connect this
5V input to EXTV CC also to maintain a 5V gate drive level.
V IN has to be sequenced on before EXTV CC , and EXTV CC
must be sequenced off before V IN .
Differential Remote Sense Amplifier
An accurate differential remote sense amplifier is provided
to sense low output voltages accurately at the remote
load points. This is especially true for high current loads.
The amplifier can be used on one of the two channels, or
on a single parallel output. It is very important that the
DIFFP and DIFFN are connected properly at the output,
and DIFFOUT is connected to either V OUTS1 or V OUTS2 .
In parallel operation, the DIFFP and DIFFN are connected
properly at the output, and DIFFOUT is connected to
one of the V OUTS pins. Review the parallel schematics in
Figure 31 and review Figure 2.
SW Pins
The SW pins are generally for testing purposes by moni-
toring these pins. These pins can also be used to dampen
out switch node ringing caused by LC parasitic in the
switched current paths. Usually a series R-C combina-
tion is used, called a snubber circuit. The resistor will
dampen the resonance and the capacitor is chosen to
only affect the high frequency ringing across the resistor.
If the stray inductance or capacitance can be measured or
approximated then a somewhat analytical technique can
be used to select the snubber values. The inductance is
usually easier to predict. It combines the power path board
inductance in combination with the MOSFET interconnect
bond wire inductance.
First the SW pin can be monitored with a wide bandwidth
scope with a high frequency scope probe. The ring fre-
quency can be measured for its value. The impedance Z
can be calculated:
Z L = 2πfL,
where f is the resonant frequency of the ring, and L is the
total parasitic inductance in the switch path. If a resistor
is selected that is equal to Z, then the ringing should be
dampened. The snubber capacitor value is chosen so that
its impedance is equal to the resistor at the ring frequency.
Calculated by: Z C = 1/(2πfC). These values are a good place
to start with. Modification to these components should
be made to attenuate the ringing with the least amount
the power loss.
Temperature Diode Monitoring
The LTM4628 has an on board 1N4148 silicon diode at the
TEMP pin that can be used to monitor temperature. The
diode is mounted very close to internal power switches.
The forward voltage of a silicon diode is temperature
dependent based on the following equation:
? η ? V T ?
or
I
I S
where I D is the diode current, V D is the diode voltage, η is
the ideality factor (typically close to 1.0) and I S (satura-
tion current) is a process dependent parameter. V T can
be broken out to:
k?T
q
where T is the diode junction temperature in Kelvin, q is
the electron charge and k is Boltzmann’s constant. V T is
approximately 26mV at room temperature (298K) and
scales linearly with Kelvin temperature. It is this linear
4628fe
18
For more information www.linear.com/LTM4628
相关PDF资料 |
PDF描述 |
|---|---|
| IFSC1008ABER220M01 | INDUCTOR POWER 22UH 0.5A SMD |
| GSC10DRYI | CONN EDGECARD 20POS DIP .100 SLD |
| AT24C08B-TH-T | IC EEPROM 8KBIT 1MHZ 8TSSOP |
| T95Z226K016LSAL | CAP TANT 22UF 16V 10% 2910 |
| 346-080-540-202 | CARDEDGE 80POS DUAL .125 GREEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1666A | 功能描述:BOARD DEMO LED DRIVER LT3791 RoHS:否 类别:编程器，开发系统 >> 评估板 - LED 驱动器 系列:- 标准包装:1 系列:PowerWise® 电流 - 输出 / 通道:20mA 输出及类型:1，非隔离 输出电压:17V 特点:可调光 输入电压:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相关产品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| DC1667 | 制造商:INTRONICS 制造商全称:INTRONICS 功能描述:15 Watt Triple Output DC-DC Converters |
| DC1668 | 制造商:INTRONICS 制造商全称:INTRONICS 功能描述:15 Watt Triple Output DC-DC Converters |
| DC1669 | 制造商:INTRONICS 制造商全称:INTRONICS 功能描述:15 Watt Triple Output DC-DC Converters |
| DC1669A | 功能描述:BOARD EVAL LTM4627 RoHS:否 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:LTM®, uModule® 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
发布紧急采购，3分钟左右您将得到回复。