- 您现在的位置：买卖IC网 > PDF目录20400 > DC1663A (Linear Technology)DEMO BOARD LTM4628 PDF资料下载
参数资料
| 型号： | DC1663A |
| 厂商： | Linear Technology |
| 文件页数： | 8/36页 |
| 文件大小： | 0K |
| 描述： | DEMO BOARD LTM4628 |
| 软件下载： | LTM4628 Spice Model |
| 设计资源： | LTM4628 Gerber Files DC1663A Design Files |
| 标准包装： | 1 |
| 系列： | µModule® |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 2，非隔离 |
| 输出电压： | 1.2V，1.5V |
| 电流 - 输出： | 8A，8A |
| 输入电压： | 4.5 ~ 26.5 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 400kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | LTM4628 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTM4628
PIN FUNCTIONS
(Recommended to Use Test Points to Monitor Signal Pin Connections.)
TRACK1, TRACK2 (E5, D8): Output Voltage Tracking Pin
and Soft-Start Inputs. Each channel has a 1.3μA pull-up
current source. When one channel is configured to be
master of the two channels, then a capacitor from this pin
to ground will set a soft-start ramp rate. The remaining
channel can be set up as the slave, and have the master’s
output applied through a voltage divider to the slave out-
put’s track pin. This voltage divider is equal to the slave
output’s feedback divider for coincidental tracking. See
the Applications Information section.
COMP1, COMP2 (E6, E7): Current control threshold and
error amplifier compensation point for each channel. The
current comparator threshold increases with this control
voltage. Tie the COMP pins together for parallel operation.
The device is internal compensated.
DIFFP (E8): Positive input of the remote sense amplifier.
This pin is connected to the remote sense point of the output
voltage. Use of the remote sense amplifier is limited to an
output voltage between 0.6V and 3.3V inclusive. Connect to
GND if not used. See the Applications Information section.
DIFFN (E9): Negative input of the remote sense amplifier.
This pin is connected to the remote sense point of the
output GND. See the Applications Information section.
MODE_PLLIN (F4): Force Continuous Mode, Burst Mode
Operation, or Pulse-Skipping Mode Selection Pin and
External Synchronization Input to Phase Detector Pin.
Connect this pin to SGND to force both channels into
force continuous mode of operation. Connect to INTV CC
to enable pulse-skipping mode of operation. Leaving the
pin floating will enable Burst Mode operation. A clock on
the pin will force both channels into continuous mode of
operation and synchronized to the external clock applied
to this pin.
RUN1, RUN2 (F5, F9): Run Control Pin. A voltage above
1.25V will turn on each channel in the module. A voltage
below 1.25V on the RUN pin will turn off the related chan-
nel. Each RUN pin has a 1μA pull-up current, once the
RUN pin reaches 1.2V an additional 4.5μA pull-up current
is added to this pin.
DIFFOUT (F8): Internal Remote Sense Amplifier Output.
Connect this pin to V OUTS1 or V OUTS2 depending on which
output is using remote sense. In parallel operation con-
nect one of the V OUTS pin to DIFFOUT for remote sensing.
Leave floating if the remote sense amplifier is not used.
SW1, SW2 (G2, G11): Switching node of each channel
that is used for testing purposes. Also an R-C snubber
network can be applied to reduce or eliminate switch node
ringing, otherwise leave floating. See the Applications
Information section.
PHASMD (G4): Connect this pin to SGND, INTV CC , or float-
ing this pin to select the phase of CLKOUT to 60 degrees,
120 degrees, and 90 degrees respectively.
CLKOUT (G5): Clock output with phase control using the
PHASMD pin to enable multiphase operation between
devices. See the Applications Information section.
PGOOD1, PGOOD2 (G9, G8): Output Voltage Power
Good Indicator. Open drain logic output that is pulled to
ground when the output voltage is not within ±7.5% of
the regulation point.
INTV CC (H8): Internal 5V Regulator Output. The control
circuits and internal gate drivers are powered from this
voltage. INTV CC is controlled and enabled when RUN1 or
RUN2 is activated high. Decouple this pin to PGND with
a 4.7μF low ESR tantalum or ceramic.
TEMP (J6): Onboard Temperature Diode for Monitoring
the VBE Junction Voltage Change with Temperature. See
the Applications Information section.
EXTV CC (J7): External power input that is enabled through
a switch to INTV CC whenever EXTV CC is greater than 4.7V.
Do not exceed 6V on this input, and connect this pin to
V IN when operating V IN on 5V. An efficiency increase will
occur that is a function of the (V IN – INTV CC ) multiplied by
power MOSFET driver current. Typical current requirement
is 30mA. V IN must be applied before EXTV CC , and EXTV CC
must be removed before V IN .
V IN (M2-M11, L2-L11, J2-J4, J9-J11, K2-K4, K9-K11):
Power Input Pins. Apply input voltage between these pins
and GND pins. Recommend placing input decoupling
capacitance directly between V IN pins and GND pins.
4628fe
8
For more information www.linear.com/LTM4628
相关PDF资料 |
PDF描述 |
|---|---|
| IFSC1008ABER220M01 | INDUCTOR POWER 22UH 0.5A SMD |
| GSC10DRYI | CONN EDGECARD 20POS DIP .100 SLD |
| AT24C08B-TH-T | IC EEPROM 8KBIT 1MHZ 8TSSOP |
| T95Z226K016LSAL | CAP TANT 22UF 16V 10% 2910 |
| 346-080-540-202 | CARDEDGE 80POS DUAL .125 GREEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1666A | 功能描述:BOARD DEMO LED DRIVER LT3791 RoHS:否 类别:编程器，开发系统 >> 评估板 - LED 驱动器 系列:- 标准包装:1 系列:PowerWise® 电流 - 输出 / 通道:20mA 输出及类型:1，非隔离 输出电压:17V 特点:可调光 输入电压:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相关产品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| DC1667 | 制造商:INTRONICS 制造商全称:INTRONICS 功能描述:15 Watt Triple Output DC-DC Converters |
| DC1668 | 制造商:INTRONICS 制造商全称:INTRONICS 功能描述:15 Watt Triple Output DC-DC Converters |
| DC1669 | 制造商:INTRONICS 制造商全称:INTRONICS 功能描述:15 Watt Triple Output DC-DC Converters |
| DC1669A | 功能描述:BOARD EVAL LTM4627 RoHS:否 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:LTM®, uModule® 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
发布紧急采购，3分钟左右您将得到回复。