- 您现在的位置：买卖IC网 > Datasheet目录409 > DR-TRC105-450-EV (RFM)BOARD EVALUATION 450MHZ RFM RFIC Datasheet资料下载
参数资料
| 型号： | DR-TRC105-450-EV |
| 厂商： | RFM |
| 文件页数： | 15/67页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION 450MHZ RFM RFIC |
| 标准包装： | 1 |
| 类型： | 收发器 |
| 频率： | 447MHz ~ 451MHz |
| 适用于相关产品： | TRC105 |
| 已供物品： | 2 个板，天线，电池 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
Figure 9
Note that start pattern detection is enabled only if data and clock recovery is enabled.
3.4 RSSI
The received signal strength is measured in the amplifier chains behind the second mixers. Each amplifier chain
is composed of 11 amplifiers each having a gain of 6 dB and an intermediate output at 3 dB. By monitoring the
two outputs of each stage, an estimation of the signal strength with a resolution of 3 dB and a dynamic range of
63 dB is obtained. This estimation is performed 16 times over a period of the I and Q signals and the 16 samples
are averaged to obtain a final RSSI value with a 0.5 dB step. The period of the I and Q signal is the inverse of the
deviation frequency, which is the low-IF frequency in OOK mode. The RSSI effective dynamic range can be in-
creased to 70 dB by adjusting MCFG01_IF_Gain[1..0] for less gain on high signal levels.
The RSSI block can also be used in interrupt mode by setting the bit IRQCFG0E_RSSI_Int[3] to 1. When
RXCFG14_RSSI is equal or greater than a predefined value stored in IRQCFG0F_RSSI_thld , bit IRQCFG0E_
SIG_DETECT[2] goes high and an interrupt signal RSSI_IRQ is generated on pin IRQ0 if IRQCFG0D_RX_
IRQ0[7..6] is set to 01 (see Table 10). The interrupt is cleared by writing a 1 to bit IRQCFG0E_ SIG_DETECT[2] .
If the bit RSSI_IRQ remains high, the process starts again. Figure 10 shows the timing diagram of RSSI in inter-
rupt mode.
Figure 10
3.5 Receiving in Buffered Data Mode
The receiver works in Buffered data mode when the MCFG01_Mode[7..6] bits are set to 01. In this mode, the
output of the data and clock recovery, i.e., the demodulated and resynchronized signal and the clock signal DCLK
are not sent directly to the output pins DATA and IRQ1 (DCLK). These signals are used to store the demodulated
data in blocks of 8 bits in a 64-byte FIFO. Figure 11 shows the receiver chain in this mode. The FSK and OOK
demodulators, data and clock recovery circuit and start pattern detect block work as described for Continuous
data mode, but they are used with two additional blocks, the FIFO and SPI.
www.RFM.com E-mail: info@rfm.com
? 2009-2013 by RF Monolithics, Inc.
Technical support +1.800.704.6079
Page 15 of 67
TRC105 - 05/29/13
相关PDF资料 |
PDF描述 |
|---|---|
| DR-TXC100-433 | BOARD EVALUATION 433MHZ TXC100 |
| DR-WLS1273L-EV | KIT EVAL FOR WLS1273L |
| DR7000-DK | 3G DEVELOPMENT KIT 433.92MHZ |
| DR7001-DK | 3G DEVELOPMENT KIT 315 MHZ |
| DR7003-DK | 3G DEVELOPMENT KIT 303.825 MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DRTU06D06 | 功能描述:时间延迟和计时继电器 180-240VAC/DC 1-60VDC 6A RoHS:否 制造商:Crydom 显示器类型:Hand Dial 电源电压:280 VAC 定时范围: 触点形式: 触点额定值:6 A 端接类型:DIN Rail |
| DRTU24A06 | 功能描述:时间延迟和计时继电器 180-240VAC/DC 24-280VAC 6A RoHS:否 制造商:Crydom 显示器类型:Hand Dial 电源电压:280 VAC 定时范围: 触点形式: 触点额定值:6 A 端接类型:DIN Rail |
| DRTU24A06R | 功能描述:时间延迟和计时继电器 90-140VAC/DC 24-280VAC 6A RoHS:否 制造商:Crydom 显示器类型:Hand Dial 电源电压:280 VAC 定时范围: 触点形式: 触点额定值:6 A 端接类型:DIN Rail |
| DRTU24B06 | 功能描述:时间延迟和计时继电器 90-140VAC/DC 24-280VAC 6A RoHS:否 制造商:Crydom 显示器类型:Hand Dial 电源电压:280 VAC 定时范围: 触点形式: 触点额定值:6 A 端接类型:DIN Rail |
| DRTU24B06R | 功能描述:时间延迟和计时继电器 2-24VAC/DC 24-280VAC 6A RoHS:否 制造商:Crydom 显示器类型:Hand Dial 电源电压:280 VAC 定时范围: 触点形式: 触点额定值:6 A 端接类型:DIN Rail |
发布紧急采购，3分钟左右您将得到回复。