参数资料
| 型号： | DS1863K |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/62页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR DS1863 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | 电信，无源光学网络（PON） |
| 已用 IC / 零件： | DS1863 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
Burst-Mode PON Controller
With Integrated Monitoring
TX-F LATCHED OPERATION
DETECTION OF
TX-F FAULT
TX-D OR
TX-F RESET
TX-F
TX-F NON-LATCHED OPERATION
DETECTION OF
TX-F FAULT
TX-F
Figure 5. DS1863 TX-F Timing.
FETG output is always latched in case it is triggered by
an unmasked alarm condition. Its output polarity is pro-
grammable to allow an external N or P MOSFET to open
FETG and MOD and BIAS Outputs as a
Function of TX-D and Alarm Sources
during alarms to shut off the laser diode current. If the
FETG output triggers indicating the DS1863 is in shut-
down, then it requires TX-D, soft TX-D, or cycling power
to be reset. Under all conditions when the analog outputs
are re-initialized after being disabled, all the alarms with
the exception of the V CC low ADC alarm will be cleared.
The V CC low alarm must remain active to prevent the out-
V CC >
V POA
Yes
Yes
Yes
TX-D
0
0
1
NON-MASKED
FETG ALARM
0
1
X
FETG
FETG DIR
FETG DIR
FETG DIR
MOD AND
BIAS
OUTPUTS
Enabled
Disabled
Disabled
put from attempting to operate when inadequate V CC
exists to operate the laser driver. Once adequate V CC is
present to clear the V CC low alarm, the outputs will be
enabled following the same sequence as power up.
As mentioned before the FETG is an output used to dis-
able the laser current via a series N or P MOSFET. This
requires that the FETG output is capable of sinking or
sourcing current. Because the DS1863 will not know if it
should sink or source current before V CC exceeds
V POA , which triggers the EE recall, this output will be
high impedance when V CC is below V POA . (see “ Low
Voltage Operation ” section for details and diagram).
The application circuit must use a pull-up or pull-down
resistor on this pin that pulls FETG to the alarm/shut-
down state (high for a PMOS, low for a NMOS). Once
V CC is above V POA , the DS1863 will pull the FETG out-
put to the state determined by the FETG DIR bit (Table
02h, Register 89h). FETG DIR will be 0 if an NMOS is
used and 1 if a PMOS is used.
Determining Alarm Causes
Using The I 2 C Interface
To determine the cause of the TX-F or FETG alarm, the
system processor can read the DS1863 ’ s Alarm Trap
Bytes (ATB) through the I 2 C interface (in Table 01h). The
ATB have a bit for each alarm. Any time an alarm occurs,
regardless of the mask bit ’ s state, the DS1863 sets the
corresponding bit in the ATB. Active ATB bits will remain
set until written to zeros via the I 2 C interface. On power
up the ATB will be zeros until alarms dictate otherwise.
Die Identification
DS1863 will have an ID hard coded to its die. Two reg-
isters (Table 02h bytes 86h – 87h) are assigned for this
feature. Byte 86h will read 63h to identify the part as the
DS1863, byte 87h will read to A1h (for A1 die revision).
Low-Voltage Operation
The DS1863 contains two Power-On Reset (POR) lev-
els. The lower level is a Digital POR (V POD ) and the
____________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| DS1864K | KIT EVAL FOR DS1864 |
| DS21349DK | KIT DESIGN FOR DS21349 |
| DS21352DK | KIT DESIGN FOR DS21352 |
| DS21354DK | KIT DESIGN FOR DS21354 |
| DS21458DK | KIT DESIGN FOR G511DS21458 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1863T+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| DS1864 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:SFP Laser Controller and Diagnostic IC |
| DS1864K | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| DS1864T | 制造商:Maxim Integrated Products 功能描述:DUAL TMP CTRL DAC+MONITORS,QFN - Rail/Tube |
| DS1864T+ | 功能描述:激光驱动器 SFP Laser Controller & Diagnostic IC RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。