参数资料
| 型号： | DS1863K |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 47/62页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR DS1863 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | 电信，无源光学网络（PON） |
| 已用 IC / 零件： | DS1863 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页当前第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
Burst-Mode PON Controller
With Integrated Monitoring
Table 02h, Register 89h: Config
FACTORY DEFAULT
READ ACCESS
WRITE ACCESS
MEMORY TYPE
00h
PW2
PW2
Nonvolatile (SEE)
89h
FETG DIR
TX-F EN
RESERVED
ASEL
RESERVED
RESERVED
RESERVED
RESERVED
bit7
Configure the memory location and the polarity of the digital outputs.
FETG DIR: Chooses the direction or polarity of the FETG output for normal operation.
bit0
bit7
bit6
bit5
bit4
bit3:0
0 = Under normal operation, FETG will be pulled low. (Default)
1 = Under normal operation, FETG will be pulled high.
TX-F EN:
0 = The alarm bits will immediately reflect the status of the last comparison. (Default)
1 = The alarm bits are latched until cleared by a TX-D transition or Power-down. If V CC low alarm is
enabled for either FETG or TX-F then latching is disabled until after the first V CC measurement is
made above the V CC to set-point to allow for proper operation during slow power-on cycles.
RESERVED
ASEL: Address SELect.
0 = Device Address of A2h (Default).
1 = Device-Address is equal to the value found in byte ‘ device_address ’ (Table 02h, 8Ch).
RESERVED
Table 02h, Register 8Ah: Startup Step
FACTORY DEFAULT:
READ ACCESS
WRITE ACCESS
MEMORY TYPE:
00h
PW2
PW2
Nonvolatile (SEE)
8Ah
2 12
2 11
2 10
2 9
2 8
2 7
2 6
2 5
bit7
This value will define the maximum allowed step for the upper 8 bits of IBIAS output during start-up.
bit0
____________________________________________________________________
47
相关PDF资料 |
PDF描述 |
|---|---|
| DS1864K | KIT EVAL FOR DS1864 |
| DS21349DK | KIT DESIGN FOR DS21349 |
| DS21352DK | KIT DESIGN FOR DS21352 |
| DS21354DK | KIT DESIGN FOR DS21354 |
| DS21458DK | KIT DESIGN FOR G511DS21458 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1863T+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| DS1864 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:SFP Laser Controller and Diagnostic IC |
| DS1864K | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| DS1864T | 制造商:Maxim Integrated Products 功能描述:DUAL TMP CTRL DAC+MONITORS,QFN - Rail/Tube |
| DS1864T+ | 功能描述:激光驱动器 SFP Laser Controller & Diagnostic IC RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。