- 您现在的位置：买卖IC网 > PDF目录97867 > DS21FF42 (DALLAS SEMICONDUCTOR) DATACOM, FRAMER, PBGA300 PDF资料下载
参数资料
| 型号： | DS21FF42 |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | Digital Transmission Controller |
| 英文描述： | DATACOM, FRAMER, PBGA300 |
| 封装： | 27 X 27 MM, BGA-300 |
| 文件页数： | 54/115页 |
| 文件大小： | 534K |
| 代理商： | DS21FF42 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页当前第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页
DS21FF42/DS21FT42
43 of 115
The user will always precede a read of any of the nine registers with a write. The byte written to the
register will inform the DS21Q42 which bits the user wishes to read and have cleared. The user will
write a byte to one of these registers, with a one in the bit positions he or she wishes to read and a zero in
the bit positions he or she does not wish to obtain the latest information on. When a one is written to a
bit location, the read register will be updated with the latest information. When a zero is written to a bit
position, the read register will not be updated and the previous value will be held. A write to the status
and information registers will be immediately followed by a read of the same register. The read result
should be logically AND’ed with the mask byte that was just written and this value should be written
back into the same register to insure that bit does indeed clear. This second write step is necessary
because the alarms and events in the status registers occur asynchronously in respect to their access via
the parallel port. This write–read– write scheme allows an external microcontroller or microprocessor to
individually poll certain bits without disturbing the other bits in the register. This operation is key in
controlling the DS21Q42 with higher–order software languages.
The SR1, SR2, and FDLS registers have the unique ability to initiate a hardware interrupt via the INT*
output pin. Each of the alarms and events in the SR1, SR2, and HSR can be either masked or unmasked
from the interrupt pin via the Interrupt Mask Register 1 (IMR1), Interrupt Mask Register 2 (IMR2), and
HDLC Interrupt Mask Register (HIMR) respectively. The FIMR register is covered in Section 19. The
INTERRUPT STATUS REGISTER can be used to determine which framer is requesting interrupt
servicing and the type of the request: status or the HDLC controller.
The interrupts caused by alarms in SR1 (namely RYEL, RCL, RBL, RLOS and LOTC) act differently
than the interrupts caused by events in SR1 and SR2 (namely LUP, LDN, RSLIP, RMF, TMF, SEC,
RFDL, TFDL, RMTCH, RAF, and RSC) and HIMR. The alarm caused interrupts will force the INT* pin
low whenever the alarm changes state (i.e., the alarm goes active or inactive according to the set/clear
criteria in Table 11-1). The INT* pin will be allowed to return high (if no other interrupts are present)
when the user reads the alarm bit that caused the interrupt to occur even if the alarm is still present.
The event caused interrupts will force the INT* pin low when the event occurs. The INT* pin will be
allowed to return high (if no other interrupts are present) when the user reads the event bit that caused the
interrupt to occur.
ISR: INTERRUPT STATUS REGISTER (Any address from A0H to FFH)
(MSB)
(LSB)
F3HDLC
F3SR
F2HDLC
F2SR
F1HDLC
F1SR
F0HDLC
F0SR
SYMBOL
POSITION
NAME AND DESCRIPTION
F3HDLC
ISR.7
FRAMER 3 HDLC CONTROLLER INTERRUPT
REQUEST.
0 = No interrupt request pending.
1 = Interrupt request pending.
F3SR
ISR.6
FRAMER 3 SR1 or SR2 INTERRUPT REQUEST.
0 = No interrupt request pending.
1 = Interrupt request pending.
相关PDF资料 |
PDF描述 |
|---|---|
| DS21FF42N | DATACOM, FRAMER, PBGA300 |
| DS21FT44N | DATACOM, FRAMER, PBGA300 |
| DS21FT44 | DATACOM, FRAMER, PBGA300 |
| DS21Q352 | DATACOM, PCM TRANSCEIVER, PBGA256 |
| DS21Q354 | DATACOM, PCM TRANSCEIVER, PBGA256 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS21FF42+ | 功能描述:网络控制器与处理器 IC 4x4 16/4x3 12 Chnl T1/T1 Framer RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21FF42N | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21FF42N+ | 功能描述:网络控制器与处理器 IC 4x4 16/4x3 12 Chnl T1/T1 Framer RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21FF44 | 功能描述:网络控制器与处理器 IC 4x4 16/4x3 12 Chnl E1/E1 Framer RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21FF44N | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。