参数资料
型号: DS21FF42
厂商: DALLAS SEMICONDUCTOR
元件分类: Digital Transmission Controller
英文描述: DATACOM, FRAMER, PBGA300
封装: 27 X 27 MM, BGA-300
文件页数: 97/115页
文件大小: 534K
代理商: DS21FF42
DS21FF42/DS21FT42
82 of 115
determining which channels are to have Bit 7 stuffing performed. If the TCR2.0 and TCR1.3 bits are set
to one, then all 24 T1 channels will have Bit 7 stuffing performed on them regardless of how the TTR
registers are programmed. In this manner, the TTR registers are only affecting which channels are to
have robbed bit signaling inserted into them. Please see Figure 24-15 for more details.
22.
INTERLEAVED PCM BUS OPERATION
In many architectures, the outputs of individual framers are combined into higher speed serial buses to
simplify transport across the system. The DS21Q42 can be configured to allow each framer’s data and
signaling busses to be multiplexed into higher speed data and signaling busses eliminating external
hardware saving board space and cost.
The interleaved PCM bus option supports two bus speeds and interleave modes. The 4.096 MHz bus
speed allows two framers to share a common bus. The 8.192 MHz bus speed allows all four of the
DS21Q42’s framers to share a common bus. Framers can interleave their data either on byte or frame
boundaries. Framers that share a common bus must be configured through software and require several
device pins to be connected together externally (see figures 22-1 & 22-2). Each framer’s elastic stores
must be enabled and configured for 2.048 MHz operation. The signal RSYNC must be configured as an
input on each framer.
For all bus configurations, one framer will be configured as the master device and the remaining framers
on the shared bus will be configured as slave devices. Refer to the IBO register description below for
more detail. In the 4.096 MHz bus configuration there is one master and one slave per bus. Figure 22-1
shows the DS21Q42 configured to support two 4.096 MHz buses. Bus 1 consists of framers 0 and 1.
Bus 2 consists of framers 2 and 3. Framers 0 and 2 are programmed as master devices. Framers 1 and 3
are programmed as slave devices. In the 8.192 MHz bus configuration there is one master and three
slaves.
Figure 22-2 shows the DS21Q42 configured to support a 8.192 MHz bus.
Framers 0 is
programmed as the master device. Framers 1, 2 and 3 are programmed as slave devices. Consult timing
diagrams in section 24 for additional information.
When using the frame interleave mode, all framers that share an interleaved bus must have receive
signals (RPOS & RNEG) that are synchronous with each other. The received signals must originate
from the same clock reference. This restriction does not apply in the byte interleave mode.
相关PDF资料
PDF描述
DS21FF42N DATACOM, FRAMER, PBGA300
DS21FT44N DATACOM, FRAMER, PBGA300
DS21FT44 DATACOM, FRAMER, PBGA300
DS21Q352 DATACOM, PCM TRANSCEIVER, PBGA256
DS21Q354 DATACOM, PCM TRANSCEIVER, PBGA256
相关代理商/技术参数
参数描述
DS21FF42+ 功能描述:网络控制器与处理器 IC 4x4 16/4x3 12 Chnl T1/T1 Framer RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS21FF42N 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS21FF42N+ 功能描述:网络控制器与处理器 IC 4x4 16/4x3 12 Chnl T1/T1 Framer RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS21FF44 功能描述:网络控制器与处理器 IC 4x4 16/4x3 12 Chnl E1/E1 Framer RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS21FF44N 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray