- 您现在的位置：买卖IC网 > PDF目录97867 > DS21FF42 (DALLAS SEMICONDUCTOR) DATACOM, FRAMER, PBGA300 PDF资料下载
参数资料
| 型号： | DS21FF42 |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | Digital Transmission Controller |
| 英文描述： | DATACOM, FRAMER, PBGA300 |
| 封装： | 27 X 27 MM, BGA-300 |
| 文件页数： | 92/115页 |
| 文件大小： | 534K |
| 代理商： | DS21FF42 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页当前第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页
DS21FF42/DS21FT42
78 of 115
The CCR2.0 bit should always be set to a one when the framer is inserting the FDL. More on how to use
the DS21Q42 in FDL applications is covered in a separate Application Note.
TFDL: TRANSMIT FDL REGISTER (Address = 7E Hex)
[Also used to insert Fs framing pattern in D4 framing mode; see Section 19.3]
(MSB)
(LSB)
TFDL7
TFDL6
TFDL5
TFDL4
TFDL3
TFDL2
TFDL1
TFDL0
SYMBOL
POSITION
NAME AND DESCRIPTION
TFDL7
TFDL.7
MSB of the FDL code to be transmitted
TFDL0
TFDL.0
LSB of the FDL code to be transmitted
The Transmit FDL Register (TFDL) contains the Facility Data Link (FDL) information that is to be
inserted on a byte basis into the outgoing T1 data stream. The LSB is transmitted first.
19.3 D4/SLC–96 OPERATION
In the D4 framing mode, the framer uses the TFDL register to insert the Fs framing pattern. To allow the
device to properly insert the Fs framing pattern, the TFDL register at address 7Eh must be programmed to
1Ch and the following bits must be programmed as shown: TCR1.2=0 (source Fs data from the TFDL
register) CCR2.5=1 (allow the TFDL register to load on multiframe boundaries)
Since the SLC–96 message fields share the Fs–bit position, the user can access the these message fields
via the TFDL and RFDL registers. Please see the separate Application Note for a detailed description of
how to implement a SLC–96
20.
PROGRAMMABLE IN–BAND CODE GENERATION AND DETECTION
Each framer in the DS21Q42 has the ability to generate and detect a repeating bit pattern that is from one
to eight bits in length. To transmit a pattern, the user will load the pattern to be sent into the Transmit
Code Definition (TCD) register and select the proper length of the pattern by setting the TC0 and TC1
bits in the In–Band Code Control (IBCC) register.
Once this is accomplished, the pattern will be
transmitted as long as the TLOOP control bit (CCR3.1) is enabled.
Normally (unless the transmit
formatter is programmed to not insert the F–bit position) the framer will overwrite the repeating pattern
once every 193 bits to allow the F–bit position to be sent. See Figure 24-15 for more details. As an
example, if the user wished to transmit the standard “loop up” code for Channel Service Units which is a
repeating pattern of ...10000100001... then 80h would be loaded into TDR and the length would set to 5
bits.
Each framer can detect two separate repeating patterns to allow for both a “loop up” code and a “loop
down” code to be detected. The user will program the codes to be detected in the Receive Up Code
Definition (RUPCD) register and the Receive Down Code Definition (RDNCD) register and the length of
each pattern will be selected via the IBCC register. The framer will detect repeating pattern codes in both
framed and unframed circumstances with bit error rates as high as 10**–2. The code detector has a
nominal integration period of 48 ms. Hence, after about 48 ms of receiving either code, the proper status
bit (LUP at SR1.7 and LDN at SR1.6) will be set to a one. Normally codes are sent for a period of 5
seconds. It is recommend that the software poll the framer every 100 ms to 1000 ms until 5 seconds has
elapsed to insure that the code is continuously present.
相关PDF资料 |
PDF描述 |
|---|---|
| DS21FF42N | DATACOM, FRAMER, PBGA300 |
| DS21FT44N | DATACOM, FRAMER, PBGA300 |
| DS21FT44 | DATACOM, FRAMER, PBGA300 |
| DS21Q352 | DATACOM, PCM TRANSCEIVER, PBGA256 |
| DS21Q354 | DATACOM, PCM TRANSCEIVER, PBGA256 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS21FF42+ | 功能描述:网络控制器与处理器 IC 4x4 16/4x3 12 Chnl T1/T1 Framer RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21FF42N | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21FF42N+ | 功能描述:网络控制器与处理器 IC 4x4 16/4x3 12 Chnl T1/T1 Framer RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21FF44 | 功能描述:网络控制器与处理器 IC 4x4 16/4x3 12 Chnl E1/E1 Framer RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21FF44N | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。