- 您现在的位置：买卖IC网 > PDF目录19362 > DSP56311VF150R2 (Freescale Semiconductor)IC DSP 24BIT 150MHZ 196-BGA PDF资料下载
参数资料
| 型号： | DSP56311VF150R2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 89/96页 |
| 文件大小： | 0K |
| 描述： | IC DSP 24BIT 150MHZ 196-BGA |
| 标准包装： | 750 |
| 系列： | DSP56K/Symphony |
| 类型： | 定点 |
| 接口： | 主机接口，SSI，SCI |
| 时钟速率： | 150MHz |
| 非易失内存： | ROM（576 B） |
| 芯片上RAM： | 384kB |
| 电压 - 输入/输出： | 3.30V |
| 电压 - 核心： | 1.80V |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 196-LBGA |
| 供应商设备封装： | 196-MAPBGA（15x15） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页当前第89页第90页第91页第92页第93页第94页第95页第96页
External Memory Expansion Port (Port A)
DSP56311 Technical Data, Rev. 8
Freescale Semiconductor
1-5
1.5.2
External Data Bus
1.5.3
External Bus Control
Table 1-7.
External Data Bus Signals
Signal
Name
Type
State During
Reset
State During
Stop or Wait
Signal Description
D[0–23]
Input/ Output
Ignored Input
Last state:
Input: Ignored
Output:
Last value
Data Bus—When the DSP is the bus master, D[0–23] are active-high,
bidirectional input/outputs that provide the bidirectional data bus for
external program and data memory accesses. Otherwise, D[0–23]
drivers are tri-stated. If the last state is output, these lines have weak
keepers to maintain the last output state if all drivers are tri-stated.
Table 1-8.
External Bus Control Signals
Signal
Name
Type
State During Reset,
Stop, or Wait
Signal Description
AA[0–3]
RAS[0–3]
Output
Tri-stated
Address Attribute—When defined as AA, these signals can be used as chip selects
or additional address lines. The default use defines a priority scheme under which
only one AA signal can be asserted at a time. Setting the AA priority disable (APD) bit
(Bit 14) of the Operating Mode Register, the priority mechanism is disabled and the
lines can be used together as four external lines that can be decoded externally into
16 chip select signals.
Row Address Strobe—When defined as RAS, these signals can be used as RAS for
DRAM interface. These signals are tri-statable outputs with programmable polarity.
Note: DRAM access is not supported above 100 MHz.
RD
Output
Tri-stated
Read Enable—When the DSP is the bus master, RD is an active-low output that is
asserted to read external memory on the data bus (D[0–23]). Otherwise, RD is tri-
stated.
WR
Output
Tri-stated
Write Enable—When the DSP is the bus master, WR is an active-low output that is
asserted to write external memory on the data bus (D[0–23]). Otherwise, the signals
are tri-stated.
TA
Input
Ignored Input
Transfer Acknowledge—If the DSP56311 is the bus master and there is no external
bus activity, or the DSP56311 is not the bus master, the TA input is ignored. The TA
input is a data transfer acknowledge (DTACK) function that can extend an external
bus cycle indefinitely. Any number of wait states (1, 2. . .infinity) can be added to the
wait states inserted by the bus control register (BCR) by keeping TA deasserted. In
typical operation, TA is deasserted at the start of a bus cycle, asserted to enable
completion of the bus cycle, and deasserted before the next bus cycle. The current
bus cycle completes one clock period after TA is deasserted. The number of wait
states is determined by the TA input or by the BCR, whichever is longer. The BCR
sets the minimum number of wait states in external bus cycles. In order to use the TA
functionality, the BCR must be programmed to at least one wait state. A zero wait
state access cannot be extended by TA deassertion.
At operating frequencies
≤100 MHz, TA can operate synchronously (with respect to
CLKOUT) or asynchronously depending on the setting of the TAS bit in the Operating
Mode Register (OMR). If synchronous mode is selected, the user is responsible for
ensuring that TA transitions occur synchronous to CLKOUT to ensure correct
operation. Synchronous operation is not supported above 100 MHz and the
OMR[TAS] bit must be set to synchronize the TA signal with the internal clock.
相关PDF资料 |
PDF描述 |
|---|---|
| UBA2016AP/1,112 | IC LAMP DVR FLUORES 600V 20-DIP |
| T525D477M2R5ATE025 | CAP TANT 470UF 2.5V 20% 2917 |
| RBM12DCWS | CONN EDGECARD 24POS DIP .156 SLD |
| AGL125V2-FGG144 | IC FPGA IGLOO 1.2-1.5V 144FPBGA |
| T525D337M003ATE025 | CAP TANT 330UF 3V 20% 2917 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DSP56311VF160 | 功能描述:数字信号处理器和控制器 - DSP, DSC SSP26111VF160A RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSP56311VL150 | 功能描述:数字信号处理器和控制器 - DSP, DSC 24 BIT DSP PBFREE RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSP56311VL150B1 | 功能描述:数字信号处理器和控制器 - DSP, DSC 24 BIT DSP PBFREE RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSP56311VL150R2 | 功能描述:数字信号处理器和控制器 - DSP, DSC 24 BIT DSP PBFREE RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSP56311VL160 | 功能描述:数字信号处理器和控制器 - DSP, DSC 24 BIT DSP PBFREE RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。