- 您现在的位置：买卖IC网 > PDF目录239729 > IBM25PPC750GXEBB2532T 32-BIT, 800 MHz, RISC PROCESSOR, CBGA292 PDF资料下载
参数资料
| 型号： | IBM25PPC750GXEBB2532T |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, 800 MHz, RISC PROCESSOR, CBGA292 |
| 封装： | 21 X 21 MM, 1 MM PITCH, CERAMIC, BGA-292 |
| 文件页数： | 62/74页 |
| 文件大小： | 1054K |
| 代理商： | IBM25PPC750GXEBB2532T |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页当前第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页
Datasheet
IBM PowerPC 750GX RISC Microprocessor
DD1.X
750GX_ds_body.fm SA14-2765-02
September 2, 2005
System Design Information
Page 65 of 73
Heat generated on the active side (ball) of the chip is conducted through the silicon, then through the heat-
sink attach material (or thermal interface material), and finally to the heat sink; where it is removed by forced-
air convection. Since the silicon thermal resistance is quite small, for a first-order analysis, the temperature
drop in the silicon may be neglected. Thus, the heat sink attach material and the heat-sink conduc-
tion/convective thermal resistances are the dominant terms.
5.7.4 Adhesives and Thermal Interface Materials
A thermal interface material is required at the package die-surface-to-heat-sink interface to minimize the
thermal contact resistance. For those applications where the heat sink is attached by a spring clip mecha-
nism, Figure 5-9 on page 66 shows an example of the thermal performance of three thin-sheet thermal-inter-
face materials (silicon, graphite/oil, floroether oil), a bare joint, and a joint with synthetic grease, as a function
of contact pressure. As shown, the performance of these thermal interface materials improves with increasing
contact pressure. The use of synthetic grease significantly reduces the interface thermal resistance. That is,
the bare joint results in a thermal resistance approximately seven times greater than the synthetic grease
joint. Customers are advised to investigate alternative thermal interface materials to ensure the most reliable,
efficient, and cost-effective thermal design.
An example of heat-sink attachment to the package by means of a spring clip to holes in the printed-circuit
board is illustrated in Figure 5-7, Package Exploded Cross-Sectional View with Several Heat-Sink Options,
on page 62. Therefore the synthetic grease offers the best thermal performance, considering the low inter-
face pressure. Of course, the selection of any thermal interface material depends on many factors—thermal
performance requirements, manufacturability, service temperature, dielectric properties, cost, and so forth.
Figure 5-8. C4 Package with Heat Sink Mounted to a Printed-Circuit Board
External Resistance Components
Internal Resistance Components
(Note the internal versus external package resistance.)
Radiation
Convection
Radiation
Convection
Custom/Application Specific
Die Junction to Case
Printed-Circuit Board
Thermal Interface Material
Die Junction to Lead
Chip Junction
(Package and Die)
(Defined by Customer Application)
Heat Sink
(Die surface)
Resistance
(Package and Leads)
(Defined by Board Design and Layout)
RJC
RJB
相关PDF资料 |
PDF描述 |
|---|---|
| ICS843023AGT | 320 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| IRFR9121 | 5.9 A, 80 V, 0.6 ohm, P-CHANNEL, Si, POWER, MOSFET, TO-252AA |
| IM1P-67202AV-25 | 1K X 9 OTHER FIFO, 25 ns, CDIP28 |
| IM3P-67202AL-45 | 1K X 9 OTHER FIFO, 45 ns, PDIP28 |
| IMDP-67202AL-25 | 1K X 9 OTHER FIFO, 25 ns, CDFP28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IBM25PPC750GXEBB2562T | 制造商:IBM 功能描述: |
| IBM25PPC750GXEBB2563T | 制造商:IBM 功能描述: |
| IBM25PPC750GXECB2563T | 制造商:IBM 功能描述: |
| IBM25PPC750GXECB2H33T | 制造商:IBM 功能描述: |
| IBM25PPC750GXECB5H42V | 制造商:IBM 功能描述:POLARIS 1.2 ? 21CBGA GRE2 ? HALFMODE 933MH - Trays |
发布紧急采购，3分钟左右您将得到回复。