参数资料
| 型号： | ISL62773IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 27/37页 |
| 文件大小： | 0K |
| 描述： | IC PWM REG MULTIPH AMD 48-QFN |
| 标准包装： | 4,000 |
| 系列： | Robust Ripple Regulator™ (R³) |
| 应用： | 控制器，AMD Fusion? SVI 2.0 CPU GPU |
| 输入电压： | 4.5 V ~ 25 V |
| 输出数： | 2 |
| 输出电压： | 0.006 V ~ 1.55 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN（6x6） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
ISL62773
Thermal Monitor [NTC, NTC_NB]
TABLE 13. FAULT PROTECTION SUMMARY
The ISL62773 features two thermal monitors which use an
external resistor network which includes an NTC thermistor to
monitor motherboard temperature and alert the AMD CPU of a
thermal issue. Figure 20 shows the basic thermal monitor circuit
FAULT TYPE
Overcurrent
FAULT DURATION
BEFORE
PROTECTION
7.5μs to 11.5μs
PROTECTION
ACTION
FAULT
RESET
PWM tri-state.
on the Core VR NTC pin. The Northbridge VR features the same
thermal monitor. The controller drives a 30μA current out of the
NTC pin and monitors the voltage at the pin. The current flowing
out of the NTC pin creates a voltage that is compared to a
warning threshold of 640mV. When the voltage at the NTC pin
falls to this warning threshold or below, the controller asserts
VR_HOT_L to alert the AMD CPU to throttle back load current to
stabilize the motherboard temperature. A thermal fault counter
begins counting toward a minimum shutdown time of 100μs.
The thermal fault counter is an up/down counter, so if the
voltage at the NTC pin rises above the warning threshold, it will
count down and extend the time for a thermal fault to occur. The
warning threshold does have 20mV of hysteresis.
Phase Current
Unbalance
Way-Overcurrent
(1.5xOC)
Undervoltage
-325mV
Overvoltage
+325mV
1ms
Immediately
PWM tri-state,
PGOOD latched
low
PGOOD latched
low.
ENABLE
toggle or
PGOOD latched VDD toggle
low.
Actively pulls the
output voltage to
below VID value,
then tri-state.
If the voltage at the NTC pin continues to fall down to the
shutdown threshold of 580mV or below, the controller goes into
shutdown and triggers a thermal fault. The PGOOD pin is pulled
low and tri-states the power MOSFETs. A fault on either side will
shutdown both VRs.
NTC Thermal 100μs min
Fault Recovery
PGOOD latched
low.
PWM tri-state.
All of the previously described fault conditions can be reset by
bringing ENABLE low or by bringing VDD below the POR
threshold. When ENABLE and VDD return to their high operating
INTERNAL TO
ISL62773
+V
levels, the controller resets the faults and soft-start occurs.
Interface Pin Protection
R p
+
V NTC
NTC
R NTC
30μA
MONITOR
VR_HOT_L
R
The SVC and SVD pins feature protection diodes which must be
considered when removing power to VDD and VDDIO, but leaving
it applied to these pins. Figure 21 shows the basic protection on
the pins. If SVC and/or SVD are powered but VDD is not, leakage
current will flow from these pins to VDD.
-
R s
Warning
640mV
Shutdown
580mV
INTERNAL TO
ISL62773
VDD
FIGURE 20. CIRCUITRY ASSOCIATED WITH THE THERMAL MONITOR
FEATURE OF THE ISL62773
As the board temperature rises, the NTC thermistor resistance
decreases and the voltage at the NTC pin drops. When the
voltage on the NTC pin drops below the over-temperature trip
threshold, then VR_HOT is pulled low. The VR_HOT signal is used
to change the CPU operation and decrease power consumption.
With the reduction in power consumption by the CPU, the board
temperature decreases and the NTC thermistor voltage rises.
Once the over-temperature threshold is tripped and VR_HOT is
taken low, the over-temperature threshold changes to the reset
level. The addition of hysteresis to the over-temperature
threshold prevents nuisance trips. Once both pin voltages exceed
the over-temperature reset threshold, the pull-down on VR_HOT
is released. The signal changes state and the CPU resumes
normal operation. The over-temperature threshold returns to the
trip level.
Table 13 summarizes the fault protections.
27
SVC, SVD
GND
FIGURE 21. PROTECTION DEVICES ON THE SVC AND SVD PINS
March 7, 2012
FN8263.0
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6277HRZ | IC PWM REG MULTIPH AMD 48-QFN |
| ISL62870HRUZ-T | IC REG CTRLR BUCK PWM 16-TQFN |
| ISL62872HRUZ-T | IC REG CTRLR BUCK PWM 20-TQFN |
| ISL62873HRUZ-T | IC REG CTRLR BUCK PWM 16UTQFN |
| ISL62875HRUZ-T | IC REG CTRLR BUCK PWM 20UTQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6277A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Multiphase PWM Regulator for AMD Fusion Mobile CPUs Using SVI 2.0 |
| ISL6277AHRZ | 制造商:Intersil Corporation 功能描述:MULTI-OUTPUT CONTROLLER FOR AMD FUSION UP, 6X6 QFN - Rail/Tube 制造商:Intersil Corporation 功能描述:IC PWM REG MULTIPH AMD 48-QFN 制造商:Intersil 功能描述:PWM Regulator for AMD Fusion |
| ISL6277AHRZ-T | 制造商:Intersil Corporation 功能描述:MULTI-OUTPUT CONTROLLER FOR AMD FUSION UP, 6X6 QFN, T&R - Tape and Reel 制造商:Intersil Corporation 功能描述:IC PWM REG MULTIPH AMD 48-QFN 制造商:Intersil 功能描述:PWM Regulator --- for AMD Fusion--- |
| ISL6277AIRZ | 功能描述:电流型 PWM 控制器 Multi-output Controller for AMD fusion uP, 6X6 QFN RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6277AIRZ-T | 功能描述:电流型 PWM 控制器 Multi-output Controller for AMD fusion uP, 6X6 QFN, T&R RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。