- 您现在的位置：买卖IC网 > PDF目录20679 > ISL6329CRZ (Intersil)IC CTRLR PWM SYNC BUCK DL 60QFN PDF资料下载
参数资料
| 型号： | ISL6329CRZ |
| 厂商： | Intersil |
| 文件页数： | 22/38页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM SYNC BUCK DL 60QFN |
| 标准包装： | 43 |
| 应用： | 控制器，AMD SVI |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 2 |
| 输出电压： | 0.0125 V ~ 1.55 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | * |
| 封装/外壳： | * |
| 供应商设备封装： | * |
| 包装： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
ISL6329
the lower MOSFET to control the output voltage until the
overvoltage event ceases or the input power supply cuts off. For
complete protection, the low side MOSFET should have a gate
threshold well below the maximum voltage rating of the
load/microprocessor.
In the event that during normal operation if the PVCC, VCC or
GVOT voltage falls back below the POR threshold, the pre-POR
overvoltage protection circuitry reactivates to protect from any
more pre-POR overvoltage events.
Undervoltage Detection
The undervoltage threshold is set at VDAC - 300mV typical. When
the output voltage (VSEN-RGND) is below the undervoltage
threshold, PGOOD gets pulled low. No other action is taken by the
controller. PGOOD will return high if the output voltage rises
above VDAC - 250mV typical.
fault is cleared or for a total of seven attempts. If the fault is not
cleared on the final attempt, the controller disables UGATE and
LGATE signals for both Core and Northbridge and latches off
requiring a POR of VCC to reset the ISL6329.
OUTPUT CURRENT, 50A/DIV
0A
OUTPUT VOLTAGE,
500mV/DIV
Overcurrent Protection
The ISL6329 takes advantage of the proportionality between the
0V
3ms/DIV
I OCP = 100 μ A ? ---- ? ------------------ – ? ------------------------------------------- ? ---------------- ?
N R ISEN ? V IN – N T V OUT V OUT ?
DCR ? 2 T L T f S V IN ?
load current and the average current, I AVG , to detect an
detail on how the average current is measured. Once the average
current exceeds 100μA, a comparator triggers the converter to
begin overcurrent protection procedures.
The overcurrent trip threshold is dictated by the DCR of the
inductors, the number of active channels, the DC gain of the
inductor RC filter and the R ISEN resistor. The overcurrent trip
threshold is shown in Equation 21.
(EQ. 21)
K
FIGURE 14. OVERCURRENT BEHAVIOR IN HICCUP MODE
It is important to note that during soft-start, the overcurrent trip
point is increased by a factor of 1.4. If the fault draws enough
current to trip overcurrent during normal run mode, it may not
draw enough current during the soft-start ramp period to trip
overcurrent while the output is ramping up. If a fault of this type
is affecting the output, then the regulator will complete soft-start
and the trip-retry counter will be reset to zero. Once the regulator
has completed soft-start, the overcurrent trip point will return to
it’s nominal setting and an overcurrent shutdown will be initiated.
This will result in a continuous hiccup mode.
R 2
Where:
K = ---------------------
R 1 + R 2
Note that the energy delivered during trip-retry cycling is much
less than during full-load operation, so there is no thermal
hazard.
CORE REGULATOR OVERCURRENT
f S = Switching Frequency
Equation 21 is valid for both the Core regulator and the
Northbridge regulator. This equation includes the DC load current
as well as the total ripple current contributed by all the phases.
For the Northbridge regulator, N is 1.
During soft-start, the overcurrent trip point is boosted by a factor
of 1.4. Instead of comparing the average measured current to
100μA, the average current is compared to 140μA. Immediately
after soft-start is over, the comparison level changes to 100μA.
This is done to allow for start-up into an active load while still
supplying output capacitor in-rush current.
OVERCURRENT PROTECTION SHUTDOWN
At the beginning of overcurrent shutdown, the controller sets all
of the UGATE and LGATE signals low, puts PWM3, PWM4, PWM5,
and PWM6 (if active) in a high-impedance state, and forces
VDDPWRGD low. This turns off all of the upper and lower
MOSFETs. The system remains in this state for fixed period of
12ms. If the controller is still enabled at the end of this wait
period, it will attempt a soft-start, as shown in Figure 14. If the
fault remains, the trip-retry cycles will continue until either the
22
The ISL6329 features a Dual Overcurrent Protection (OCP)
feature on the Core that allows AMD processors to “throttle” the
load current beyond the normal OCP threshold for brief periods of
time. These current spikes occur when idle processor cores are
enabled. Dual OCP is not enabled until soft-start is complete.
When the Core average sensed current, I AVG , exceeds 100 μ A, the
Core regulator does not immediately initiate overcurrent
protection shutdown. The ISL6329 will, instead, source an
amount of current out of the OCP pin that is equivalent to the
amount of sensed current that exceeds 100 μ A. A capacitor tied
between the OCP pin and ground will immediately begin
charging. If the voltage across the capacitor, and thus the voltage
on the OCP pin, exceeds 2V then the ISL6329 will immediately
initiate overcurrent protection shutdown. If I AVG decreases to a
level below 100 μ A prior to the voltage on the OCP pin exceeding
2V, then the OCP pin is internally pulled to ground and the
voltage on the OCP capacitor is discharged. If, at any time, the
average sensed current exceeds 145 μ A, the ISL6329 will
immediately initiate overcurrent protection shutdown.
It is recommended that the maximum current spike correspond
to an average sensed current level of 120 μ A. It is also
FN7800.0
April 19, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| RSO-123.3DZ/H2 | CONV DC/DC 1W 4.5-18V +/-3.3VOUT |
| ISL6534CVZ-T | IC REG 3OUT BCK/LINEAR 24EPTSSOP |
| ASM31DRMI | CONN EDGECARD 62POS .156 SQ WW |
| GEM28DRKN | CONN EDGECARD 56POS DIP .156 SLD |
| EL7513IYZ-T13 | IC LED DRIVR WHITE BCKLGT 8-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6329CRZ-T | 功能描述:电压模式 PWM 控制器 6+1 PHS DL PWM CONTRLR FOR CORE RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6329EVAL1Z | 制造商:Intersil Corporation 功能描述:ISL6329 EVALUATION BOARD - 60 LEAD - QFN - ROHS COMPLIANT - Bulk |
| ISL6329IRZ | 功能描述:电压模式 PWM 控制器 6+1 PHS DL PWM CONTRLR FOR CORE RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6329IRZ-T | 功能描述:电压模式 PWM 控制器 6+1 PHS DL PWM CONTRLR FOR CORE RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6333ACRZ | 功能描述:IC CTRLR PWM 3PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。