- 您现在的位置：买卖IC网 > PDF目录1223 > KIT33982CEVBE (Freescale Semiconductor)KIT EVAL 33982 HIGH SIDE SWITCH PDF资料下载
参数资料
| 型号： | KIT33982CEVBE |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 25/36页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL 33982 HIGH SIDE SWITCH |
| 标准包装： | 1 |
| 主要目的： | 电源管理，高端驱动器（内部 FET） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | MC33982 |
| 主要属性： | 输出电流监控，2 个 SPI 可选电流比 |
| 次要属性： | 过电流限制SPI控制，开路负载侦测，输出开/关，转换速率 |
| 已供物品： | 板，CD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
While addressing this register, if the input was enabled for
direct control, a Logic [1] for the D0 bit will result in a Boolean
AND of the IN pin with its corresponding D0 message bit
when addressing the OCR register. Similarly, a Logic [0] on
Table 14 shows the eight selectable output switching delay
times, which range from 0 to 525 ms.
Table 14. Switching Delay
the D0 pin will result in a Boolean OR of the IN pin with the
corresponding message bits when addressing the OCR
register.
The DICR register is useful if there is a need to
independently turn on and off several loads that are PWM’d
at the same frequency and duty cycle with only one PWM
signal. This type of operation can be accomplished by
connecting the pertinent direct IN pins of several devices to a
PWM output port from the MCU, and configuring each of the
outputs to be controlled via their respective direct IN pin. The
DICR is then used to Boolean AND the direct IN(s) of each of
the outputs with the dedicated SPI bit that also controls the
output. Each configured SPI bit can now be used to enable
and disable the common PWM signal from controlling its
OSD[2:0] (D2 : D0)
000
001
010
011
100
101
110
111
Turn ON Delay (ms)
0
75
150
225
300
375
450
525
assigned output.
A Logic [1] on bit D2 is used to select the high ratio (C SR1 , ?
1/40000) on the CSNS pin. The default value [0] is used to
select the low ratio (C SR0 , 1/5400). A Logic [1] on bit D3 is
used to select the high-speed slew rate. The default value [0]
corresponds to the low-speed slew rate.
Address 0101 — Output Switching Delay Register (OSDR)
The OSDR register is used to configure the device with a
programmable time delay that is active during Output On
Address 1101 — Watchdog Register (WDR)
The WDR register is used by the MCU to configure the
watchdog timeout. Watchdog timeout is configured using bits
D1 and D0 ( Table 15 ). When bits D1 and D0 are programmed
for the desired watchdog timeout period, the WD bit (D7)
should be toggled as well to ensure that the new timeout
period is programmed at the beginning of a new count
sequence.
Table 15. Watchdog Timeout
transitions that are initiated via the SPI (not via direct input).
Whenever the input is commanded to transition from
Logic [0] to Logic [1], the output will be held OFF for the time
delay configured in the OSDR register.
The programming of the contents of this register has no
effect on device Fail-safe mode operation. The default value
of the OSDR register is 000, equating to no delay, since the
switching delay time is 0 ms. This feature allows the user a
WD [1:0] (D1: D0)
00
01
10
11
Timing (ms)
620
310
2500
1250
way to minimize inrush currents, or surges, thereby allowing
loads to be synchronously switched ON with a single
command.
Address 0110 — No Action Register (NAR)
The NAR register can be used to no-operation fill SPI data
packets in a daisy chain SPI configuration. This allows
devices to not be affected by commands being clocked over
a daisy-chained SPI configuration, and by toggling the WD bit
(D7) the watchdog circuitry will continue to be reset while no
programming or data readback functions are being requested
from the device.
33982
Analog Integrated Circuit Device Data ?
Freescale Semiconductor
25
相关PDF资料 |
PDF描述 |
|---|---|
| KIT33984CEVBE | KIT EVAL 33984 HIGH SIDE SWITCH |
| KIT33988CEVBE | KIT EVAL 33988 HIGH SIDE SWITCH |
| KIT33996EKEVB | KIT EVAL 33996 16OUTPUT SW W/SPI |
| KIT34673EPEVBE | KIT EVALUATION FOR MC34673 |
| KIT34674EPEVBE | KIT EVAL BOARD 10CH LED BACKLGHT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KIT33982PNAEVB | 功能描述:电源管理IC开发工具 SPSS HIGH-SIDE SWTCH RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT33984CEVBE | 功能描述:电源管理IC开发工具 4.0 M HIGH-SIDE SW RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT33984PNAEVB | 功能描述:电源管理IC开发工具 33984 - SPD4 EVAL KIT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT33988CEVBE | 功能描述:电源管理IC开发工具 HIGH SIDE SWITCH (8.0M) RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT33989DWEVB | 功能描述:界面开发工具 33989DW HS SBC EVAL KIT RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。