- 您现在的位置：买卖IC网 > PDF目录80478 > M38B79FFFP 8-BIT, FLASH, 4.2 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | M38B79FFFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 4.2 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | 14 X 20 MM, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件页数： | 111/112页 |
| 文件大小： | 1862K |
| 代理商： | M38B79FFFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页当前第111页第112页
95
38B7 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
q CPU reprogramming mode operation procedure
The operation procedure in CPU reprogramming mode is de-
scribed below.
< Beginning procedure >
Apply 0 V to the CNVss/VPP pin for reset release.
Set the CPU mode register. (see Figure 100)
After CPU reprogramming mode control program is transferred to
internal RAM, jump to this control program on RAM. (The follow-
ing operations are controlled by this control program).
Set “1” to the CPU reprogramming mode select bit.
Apply VPPH to the CNVSS/VPP pin.
Wait till CNVSS/VPP pin becomes 12 V.
Read the CPU reprogramming mode monitor flag to confirm
whether the CPU reprogramming mode is valid.
The operation of the flash memory is executed by software-com-
mand-writing to the flash command register .
Note: The following are necessary other than this:
Control for data which is input from the external (serial I/O
etc.) and to be programmed to the flash memory
Initial setting for ports etc.
Writing to the watchdog timer
< Release procedure >
Apply 0V to the CNVSS/VPP pin.
Wait till CNVSS/VPP pin becomes 0V.
Set the CPU reprogramming mode select bit to “0”.
Each software command is explained as follows.
q Read command
When “0016” is written to the flash command register, the
M38B79FF enters the read mode. The contents of the corre-
sponding address can be read by reading the flash memory (For
instance, with the LDA instruction etc.) under this condition.
The read mode is maintained until another command code is written
to the flash command register. Accordingly, after setting the read
mode once, the contents of the flash memory can continuously be
read.
After reset and after the reset command is executed, the read
mode is set.
Fig. 99 Flash command register bit configuration
Fig. 100 CPU mode register bit configuration in CPU rewriting
mode
Writing of software command
<Command code>
“0016”
“4016”
“C016”
“2016” + “2016”
“A016”
“FF16” + “FF16”
<Software command name>
Read command
Program command
Program verify command
Erase command
Erase verify command
Reset command
Note: The flash command register is write-only register.
Flash command register
(FCMD : address 0EFF16)
76
5
4
3
2
1
0
CPU mode register
(CPUM : address 003B16)
b7
b0
Stack page selection bit
0 : 0 page
1 : 1 page
Reserved
(Do not write “0” to this bit when using
XCIN–XCOUT oscillation function.)
Processor mode bits
b1 b0
0
0 : Single-chip mode
0
1 : Not available
1
X : Not available
Port XC switch bit
0 : I/O port function (stop oscillating)
1 : XCIN–XCOUT oscillating function
Main clock (XIN–XOUT) stop bit
0 : Oscillating
1 : Stopped
Main clock division ratio selection bits
b7 b6
0
0 :
φ = f(XIN) (high-speed mode)
0
1 :
φ = f(XIN)/4 (middle-speed mode)
1
0 :
φ = f(XCIN)/2 (low-speed mode)
1
1 : Not available
00
相关PDF资料 |
PDF描述 |
|---|---|
| MB96F346YWAXXXPMC-GSE2 | 16-BIT, FLASH, 56 MHz, RISC MICROCONTROLLER, PQFP100 |
| M30221M8-XXXFP | 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP120 |
| M37470M4-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37478E8SS | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, CDIP42 |
| MB90F343CESPF | MICROCONTROLLER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M38B79MFA053 | 制造商:Panasonic Industrial Company 功能描述:SUB ONLY IC |
| M38C13E6FP | 功能描述:IC 740 MCU OTP 24K 64LQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 产品培训模块:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 标准包装:90 系列:AVR® XMEGA 核心处理器:AVR 芯体尺寸:8/16-位 速度:32MHz 连通性:I²C，IrDA，SPI，UART/USART 外围设备:欠压检测/复位，DMA，POR，PWM，WDT 输入/输出数:50 程序存储器容量:192KB（96K x 16） 程序存储器类型:闪存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 电压 - 电源 (Vcc/Vdd):1.6 V ~ 3.6 V 数据转换器:A/D 16x12b; D/A 2x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:64-TQFP 包装:托盘 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM |
| M38C13E6HP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C13RLFS | 制造商:Renesas Electronics Corporation 功能描述:EMULATION MCU/8BIT CMOS EMULATION CHIP - Bulk |
| M38C24M4-XXXFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。