参数资料
型号: M38B79FFFP
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 4.2 MHz, MICROCONTROLLER, PQFP100
封装: 14 X 20 MM, 0.65 MM PITCH, PLASTIC, QFP-100
文件页数: 95/112页
文件大小: 1862K
代理商: M38B79FFFP
80
38B7 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Read-only Mode
The microcomputer enters the read-only mode by applying VPPL
to the VPP pin. In this mode, the user can input the address of a
memory location to be read and the control signals at the timing
shown in Figure 86, and the M38B79FF will output the contents of
the user’s specified address from data I/O pin to the external. In
this mode, the user cannot perform any operation other than read.
Fig. 86 Read timing
Read/Write Mode
The microcomputer enters the read/write mode by applying VPPH
to the VPP pin. In this mode, the user must first input a software
command to choose the operation (e. g., read, program, or erase)
to be performed on the flash memory (this is called the first cycle),
and then input the information necessary for execution of the com-
mand (e.g, address and data) and control signals (this is called
the second cycle). When this is done, the M38B79FF executes the
specified operation.
Table 15 shows the software commands and the input/output in-
formation in the first and the second cycles. The input address is
___
latched internally at the falling edge of the WE input; software
commands and other input data are latched internally at the rising
___
edge of the WE input.
The following explains each software command. Refer to Figures 87
to 89 for details about the signal input/output timings.
Table 15 Software command (parallel input/output mode)
Symbol
Read
Program
Program verify
Erase
Erase verify
Reset
Device identification
Address input
×
Verify address
×
First cycle
Data input
0016
4016
C016
2016
A016
FF16
9016
Address input
Read address
Program address
×
ADI
Second cycle
Data I/O
Read data (Output)
Program data (Input)
Verify data (Output)
2016 (Input)
Verify data (Output)
FF16 (Input)
DDI (Output)
Note: ADI = Device identification address : manufacturer’s code 0000016, device code 0000116
DDI = Device identification data : manufacturer’s code 1C16, device code D016
× can be VIL or VIH.
Address
Valid address
tRC
ta(CE)
tWRR
tDF
ta(OE)
tDH
tOLZ
Floating
tCLZ
ta(AD)
VIH
VIL
VIH
VIL
VIH
VIL
VIH
VIL
VOH
VOL
CE
OE
WE
Data
Dout
相关PDF资料
PDF描述
MB96F346YWAXXXPMC-GSE2 16-BIT, FLASH, 56 MHz, RISC MICROCONTROLLER, PQFP100
M30221M8-XXXFP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP120
M37470M4-XXXSP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32
M37478E8SS 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, CDIP42
MB90F343CESPF MICROCONTROLLER, PQFP100
相关代理商/技术参数
参数描述
M38B79MFA053 制造商:Panasonic Industrial Company 功能描述:SUB ONLY IC
M38C13E6FP 功能描述:IC 740 MCU OTP 24K 64LQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:740/38000 产品培训模块:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 标准包装:90 系列:AVR® XMEGA 核心处理器:AVR 芯体尺寸:8/16-位 速度:32MHz 连通性:I²C,IrDA,SPI,UART/USART 外围设备:欠压检测/复位,DMA,POR,PWM,WDT 输入/输出数:50 程序存储器容量:192KB(96K x 16) 程序存储器类型:闪存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 电压 - 电源 (Vcc/Vdd):1.6 V ~ 3.6 V 数据转换器:A/D 16x12b; D/A 2x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:64-TQFP 包装:托盘 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM
M38C13E6HP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C13RLFS 制造商:Renesas Electronics Corporation 功能描述:EMULATION MCU/8BIT CMOS EMULATION CHIP - Bulk
M38C24M4-XXXFP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER