- 您现在的位置：买卖IC网 > PDF目录299436 > M58BW016DB90ZA6FT (STMICROELECTRONICS) 512K X 32 FLASH 3V PROM, 90 ns, PBGA80 PDF资料下载
参数资料
| 型号： | M58BW016DB90ZA6FT |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | PROM |
| 英文描述： | 512K X 32 FLASH 3V PROM, 90 ns, PBGA80 |
| 封装： | 10 X 12 MM, 1 MM PITCH, LBGA-80 |
| 文件页数： | 21/63页 |
| 文件大小： | 901K |
| 代理商： | M58BW016DB90ZA6FT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页
28/63
STATUS REGISTER
The Status Register provides information on the
current or previous Program, Erase, Block Protect
or Tuning Protection operation. The various bits in
the Status Register convey information and errors
on the operation. They are output on DQ7-DQ0.
To read the Status Register the Read Status Reg-
ister command can be issued. The Status Register
is automatically read after Program, Erase, Block
Protect, Program/Erase Resume commands. The
Status Register can be read from any address.
The contents of the Status Register can be updat-
ed during an erase or program operation by tog-
gling the Output Enable or Output Disable pins or
by dis-activating (Chip Enable, VIH) and then reac-
tivating (Chip Enable and Output Enable, VIL, and
Output Disable, VIH.) the device.
The Status Register bits are summarized in Table
junction with the following text descriptions.
Program/Erase Controller Status (Bit 7)
The Program/Erase Controller Status bit indicates
whether the Program/Erase Controller is active or
inactive. When the Program/Erase Controller Sta-
tus bit is set to ‘0’, the Program/Erase Controller is
active; when bit7 is set to ‘1’, the Program/Erase
Controller is inactive.
The Program/Erase Controller Status is set to ‘0’
immediately after a Program/Erase Suspend com-
mand is issued until the Program/Erase Controller
pauses. After the Program/Erase Controller paus-
es the bit is set to ‘1’.
During Program and Erase operations the Pro-
gram/Erase Controller Status bit can be polled to
find the end of the operation. The other bits in the
Status Register should not be tested until the Pro-
gram/Erase Controller completes the operation
and the bit is set to ‘1’.
After the Program/Erase Controller completes its
operation the Erase Status (bit5), Program Status
and Tuning Protection Unlock status (bit4) bits
should be tested for errors.
Erase Suspend Status (Bit 6)
The Erase Suspend Status bit indicates that an
Erase operation has been suspended and is wait-
ing to be resumed. The Erase Suspend Status
should only be considered valid when the Pro-
gram/Erase Controller Status bit is set to ‘1’ (Pro-
gram/Erase Controller inactive); after a Program/
Erase Suspend command is issued the memory
may still complete the operation rather than enter-
ing the Suspend mode.
When the Erase Suspend Status bit is set to ‘0’,
the Program/Erase Controller is active or has com-
pleted its operation; when the bit is set to ‘1’, a Pro-
gram/Erase Suspend command has been issued
and the memory is waiting for a Program/Erase
Resume command.
When a Program/Erase Resume command is is-
sued the Erase Suspend Status bit returns to ‘0’.
Erase Status (Bit 5)
The Erase Status bit can be used to identify if the
memory has failed to verify that the block has
erased correctly. The Erase Status bit should be
read once the Program/Erase Controller Status bit
is High (Program/Erase Controller inactive).
When the Erase Status bit is set to ‘0’, the memory
has successfully verified that the block has erased
correctly. When the Erase Status bit is set to ‘1’,
the Program/Erase Controller has applied the
maximum number of pulses to the block and still
failed to verify that the block has erased correctly.
Once set to ‘1’, the Erase Status bit can only be re-
set to ‘0’ by a Clear Status Register command or a
hardware reset. If set to ‘1’ it should be reset be-
fore a new Program or Erase command is issued,
otherwise the new command will appear to fail.
Program Status, Tuning Protection Unlock
Status (Bit 4)
The Program Status and Tuning Protection Unlock
Status bit is used to identify a Program failure or a
Tuning Protection Code verify failure. Bit4 should
be read once the Program/Erase Controller Status
bit is High (Program/Erase Controller inactive).
When bit4 is set to ‘0’ the memory has successful-
ly verified that the device has programmed cor-
rectly or that the correct Tuning Protection Code
has been written. When bit4 is set to ‘1’ the device
has failed to verify that the data has been pro-
grammed correctly or that the correct Tuning Pro-
tection code has been written.
Once set to 1’, the Program Status bit can only be
reset to ‘0’ by a Clear Status Register command or
a hardware reset. If set to ‘1’ it should be reset be-
fore a new Program or Erase command is issued,
otherwise the new command will appear to fail.
VPP Status (Bit 3)
The VPP Status bit can be used to identify an in-
valid voltage on the VPP pin during fast program
and erase operations. The VPP pin is only sampled
at the beginning of a program or erase operation.
Indeterminate results can occur if VPP becomes in-
valid during a fast Program or Erase operation.
When the VPP Status bit is set to ‘0’, the voltage on
the VPP pin was sampled at a valid voltage; when
the VPP Status bit is set to ‘1’, the VPP pin has a
voltage that is below the VPP Lockout Voltage, VP-
PLK.
Once set to ‘1’, the VPP Status bit can only be reset
to ‘0’ by a Clear Status Register command or a
hardware reset. If set to ‘1’ it should be reset be-
相关PDF资料 |
PDF描述 |
|---|---|
| M58BW016DB90ZA3FT | 512K X 32 FLASH 3V PROM, 90 ns, PBGA80 |
| M58BW016DB80ZA6F | 512K X 32 FLASH 3V PROM, 80 ns, PBGA80 |
| M58LW032A | 32 Mbit 2Mb x16, Uniform Block, Burst 3V Supply Flash Memory |
| M58LW032A110N1T | 32 Mbit 2Mb x16, Uniform Block, Burst 3V Supply Flash Memory |
| M58LW032A110N6T | 32 Mbit 2Mb x16, Uniform Block, Burst 3V Supply Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M58BW016DB90ZA6T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16 Mbit 512Kb x32, Boot Block, Burst 3V Supply Flash Memories |
| M58BW016DBT | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16 Mbit 512Kb x32, Boot Block, Burst 3V Supply Flash Memories |
| M58BW016DBZA | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16 Mbit 512Kb x32, Boot Block, Burst 3V Supply Flash Memories |
| M58BW016DT | 制造商:NUMONYX 制造商全称:Numonyx B.V 功能描述:16 Mbit (512 Kbit x 32, boot block, burst) 3 V supply Flash memories |
| M58BW016DT100T3T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16 Mbit 512Kb x32, Boot Block, Burst 3V Supply Flash Memories |
发布紧急采购，3分钟左右您将得到回复。