- 您现在的位置：买卖IC网 > PDF目录383307 > MA28140 (Dynex Semiconductor Ltd.) Packet Telecommand Decoder PDF资料下载
参数资料
| 型号： | MA28140 |
| 厂商： | Dynex Semiconductor Ltd. |
| 英文描述： | Packet Telecommand Decoder |
| 中文描述： | 包遥控解码器 |
| 文件页数： | 18/72页 |
| 文件大小： | 857K |
| 代理商： | MA28140 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
MA28140
18/72
- The TC Segment was transferred on MAP 63 (i.e., MAP
111111), which is dedicated to the transfer of Authentication
Control Commands. In this case, the Control Command
Processor is authorised to further process the TC Segment,
which will never be transferred to the Segmentation Layer.
In both cases, the contents of the indicated LAC Register is
incremented by one.
THE CONTROL COMMAND PROCESSOR
The function of the Control Command Processor is to
execute the special TC Segments called Authentication
Control Commands after being authorised by the Final
Authorisation Function. The formats of the various
Authentication Control Commands are specified in the section
on AU Control Commands next. Any TC Segment not
conforming to the specified formats (i.e., both in length and in
contents) are rejected and reported as not executable.
THE DELETION FUNCTION
The Deletion Function deletes the Authentication Tail of all
TC Segments authorised by the Final Authorisation Function.
The complete authentication process is meant to be
transparent to an observer placed at the receiving end of the
Segmentation Layer.
AU Control Commands
It is necessary to differentiate TC Segments containing the
Authentication Control Commands required to reconfigure the
AU. This is done by allocating the TC Segment Header
contents “all ones” to these particular segments, i.e.:
- Sequence Flags set to 11 (Unsegmented)
- MAP ID set to 111111 (MAP63)
TC Segments containing the Authentication Control
Commands shall always be authenticated. The formats of the
Authentication Control Commands are organised in three
groups as follows:
- One octet of TC Segment Header for all three groups.
- One octet following the Segment Header to specify the
Control Command Identifier
- Zero, four or eight octets of Control Command Data
Field, depending on the group.
Table 2 gives the complete list of Authentication Control
Commands, with Group numbers, Control Command IDs and
Command Names. Table 3 shows the format of the TC
Segment for each Group, complete with Authentication Tail.
Each Control Command is specified in the next subsections.
DUMMY CONTROL COMMAND
The purpose of this command is to serve as NOP (No
Operation) for testing purposes. After being authenticated, this
Control Command will have no effect. However, since the AU
has authenticated the Dummy Segment, the contents of the
LAC Register used during the authorisation process have
been incremented and a telemetry report prepared
accordingly.
SELECT KEY CONTROL COMMANDS
(a) Select Fixed Key
The AU selects the Fixed Key prior to authenticating the TC
Segment:
- If authentication is successful, the Fixed Key remains
selected.
- If authentication is unsuccessful, the key previously in
use remains selected.
(b) Select Programmable Key
The AU selects the Programmable Key for authentication
of the TC Segment:
- If authentication is successful, the Programmable Key
remains selected.
- If authentication is unsuccessful, the key previously in
use remains selected.
LOAD FIXED KEY IN PROGRAMMABLE KEY MEMORY
CONTROL COMMAND
This command reloads the Fixed Key set in the
Programmable Key memory with a single command
instruction. The key used for authenticating the TC Segment
containing the Control Command will be whatever key was
selected in the AU at the time the command was transmitted.
SET NEW LAC COUNT VALUE CONTROL COMMAND
The purpose of this Control Command is to set the value of
one of the three programmable LAC Counters: Principal,
Auxiliary or Recovery with LAC Identifiers 00, 01 and 10
respectively. If the LAC Identifier is set to 11, the command is
not executed and reported as not executable. As soon as the
TC Segment is authorised by the authentication process, the
specified LAC Count value is forced into the selected LAC
Register. Note that the 22 MSBs of the 30-bit Recovery LAC
Register are permanently set to all ones, therefore those same
bits in a Set New Recovery LAC Count Value Control
Command are ignored by the AU. The key used for
authenticating the TC Segment containing the Control
Command will be whatever key was selected in the AU at the
time the command was transmitted.
相关PDF资料 |
PDF描述 |
|---|---|
| MA28151 | Radiation hard Programmable Communication Interface |
| MA28155 | Radiation Hard Programmable Peripheral Interface |
| MA31750 | High Performance MIL-STD-1750 Microprocessor |
| MA31751 | Memory Management & Block Protection Unit |
| MA31753 | DMA Controller (DMAC) For An MA31750 System |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MA28150FBB | 功能描述:专用陶瓷电容器 HF CHIP RoHS:否 制造商:Panasonic Electronic Components 电容:470 pF 容差:10 % 电压额定值:250 VAC 工作温度范围:- 25 C to + 125 C 端接类型:SMD/SMT 外壳代码 - in: 外壳代码 - mm: |
| MA28150FBN | 功能描述:专用陶瓷电容器 HF CHIP RoHS:否 制造商:Panasonic Electronic Components 电容:470 pF 容差:10 % 电压额定值:250 VAC 工作温度范围:- 25 C to + 125 C 端接类型:SMD/SMT 外壳代码 - in: 外壳代码 - mm: |
| MA28150GBB | 功能描述:专用陶瓷电容器 HF CHIP RoHS:否 制造商:Panasonic Electronic Components 电容:470 pF 容差:10 % 电压额定值:250 VAC 工作温度范围:- 25 C to + 125 C 端接类型:SMD/SMT 外壳代码 - in: 外壳代码 - mm: |
| MA28150GBN | 功能描述:专用陶瓷电容器 HF CHIP RoHS:否 制造商:Panasonic Electronic Components 电容:470 pF 容差:10 % 电压额定值:250 VAC 工作温度范围:- 25 C to + 125 C 端接类型:SMD/SMT 外壳代码 - in: 外壳代码 - mm: |
| MA28150JAB | 功能描述:专用陶瓷电容器 HF CHIP RoHS:否 制造商:Panasonic Electronic Components 电容:470 pF 容差:10 % 电压额定值:250 VAC 工作温度范围:- 25 C to + 125 C 端接类型:SMD/SMT 外壳代码 - in: 外壳代码 - mm: |
发布紧急采购，3分钟左右您将得到回复。