- 您现在的位置：买卖IC网 > PDF目录1837 > MAX1541ETL+T (Maxim Integrated Products)IC REG CTRLR DIVIDER PWM 40-TQFN PDF资料下载
参数资料
| 型号： | MAX1541ETL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 23/49页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR DIVIDER PWM 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 620kHz |
| 占空比： | 100% |
| 电源电压： | 2 V ~ 28 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 是 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
Dual Step-Down Controllers with Saturation
Protection, Dynamic Output, and Linear Regulator
nected internally to the fixed 5V linear-regulator output
(LDOOUT).
The 5V bias supply must provide V CC (PWM controller)
and V DD (gate-drive power), so the maximum current
drawn is:
I BIAS = I CC + f SW (Q G(LOW) + Q G(HIGH) )
= 4mA to 50mA (typ)
where I CC is 1.1mA (typ), f SW is the switching frequency,
and Q G(LOW) and Q G(HIGH) are the MOSFET data
sheet’s total gate-charge specification limits at V GS = 5V.
The V+ battery input and 5V bias inputs (V CC and V DD )
can be connected together if the input source is a fixed
4.5V to 5.5V supply. If the 5V bias supply powers up
prior to the battery supply, the enable signals (ON1 and
ON2 going from low to high) must be delayed until the
battery voltage is present in order to ensure startup.
Free-Running, Constant On-Time, PWM
Controller with Input Feed Forward
The Quick-PWM control architecture is a pseudofixed-
frequency, constant on-time, current-mode regulator
with voltage feed forward (Figure 2). This architecture
relies on the output filter capacitor’s ESR to act as a
current-sense resistor, so the output ripple voltage pro-
vides the PWM ramp signal. The Quick-PWM algorithm
is simple: the high-side switch on-time relies solely on
an adjustable one-shot whose pulse width is inversely
proportional to input voltage and directly proportional to
output voltage. Another one-shot sets a fixed minimum
off-time (400ns typ). The controller triggers the on-time
one-shot when the error comparator is low, the inductor
current is below the valley current-limit threshold, and
the minimum off-time one-shot has timed out.
On-Time One-Shot (TON)
The heart of the PWM core is the one-shot that sets the
high-side switch on-time. This fast, low-jitter, adjustable
one-shot includes circuitry that varies the on-time in
response to the battery and output voltages. The high-
side switch on-time is inversely proportional to the bat-
tery voltage as measured by the V+ input (V IN = V+),
where K (switching period) is set by the TON pin-strap
connection (Table 3). This algorithm results in a nearly
constant switching frequency despite the lack of a fixed-
frequency clock generator. The benefits of a constant
switching frequency are twofold: 1) the frequency can
be selected to avoid noise-sensitive regions such as the
455kHz IF band and 2) the inductor ripple-current oper-
ating point remains relatively constant, resulting in easy
design methodology and predictable output voltage rip-
ple. The on-time for the main controller (DH1) is set 15%
higher than the nominal frequency setting (200kHz,
300kHz, 420kHz, or 540kHz), while the on-time for the
secondary controller (DH2) is set 15% lower than the
nominal setting. This prevents audio-frequency “beat-
ing” between the two asynchronous regulators.
The on-time one-shot has good accuracy at the operat-
ing points specified in the Electrical Characteristics
(approximately ±12.5% at 540kHz and 420kHz nominal
settings, and ±10% with the 300kHz and 200kHz set-
tings). On-times at operating points far removed from
the conditions specified in the Electrical Characteristics
can vary over a wider range.
The constant on-time translates only roughly to a constant
switching frequency. The on-times guaranteed in the
Electrical Characteristics are influenced by resistive loss-
es and by switching delays in the high-side MOSFET.
Resistive losses—including the inductor, both MOSFETs,
and PC board copper losses in the output and ground—
tend to raise the switching frequency as the load increas-
es. The dead-time effect increases the effective on-time,
reducing the switching frequency as one or both dead
times add to the effective on-time. It occurs only in PWM
mode ( SKIP = V CC ) and during dynamic output-voltage
transitions when the inductor current reverses at light- or
negative-load currents. With reversed inductor current,
the inductor’s EMF causes LX_ to go high earlier than
normal, extending the on-time by a period equal to the
driver dead time.
For loads above the critical conduction point, where the
dead-time effect no longer occurs, the actual switching
frequency is:
t ON ( V IN DROP1 DROP2 )
and proportional to the output voltage as measured by
the OUT_ input:
f SW =
V OUT_ +V DROP1
+V - V
On- Time = K ? OUT ?
? V ?
? V IN ?
where V DROP1 is the sum of the parasitic voltage drops
in the inductor discharge path, including synchronous
rectifier, inductor, and PC board resistances; V DROP2 is
the sum of the resistances in the charging path, includ-
______________________________________________________________________________________
23
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1542ETP+T | IC DC-DC CONV TFT-LCD 20-TQFN |
| MAX1544ETL+ | IC QUICK-PWM DUAL-PHASE 40-TQFN |
| MAX1545ETL+ | IC QUICK-PWM DUAL-PHASE 40-TQFN |
| MAX1551EZK+T | IC BATT CHRGR LI+ 1CELL SOT23-5 |
| MAX1556ETB/V+T | IC REG BUCK SYNC ADJ 1.2A 10TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1541EVKIT | 制造商:Maxim Integrated Products 功能描述:DUAL STEP-DOWN CONTROLLERS W. SATURATION PROT - Bulk |
| MAX15425EVKIT# | 功能描述:显示开发工具 Eval Kit for the MAX15425 (Intel CPU Controller) RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
| MAX1542ETP | 功能描述:LCD 驱动器 RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX1542ETP+ | 功能描述:LCD 驱动器 TFT LCD DC/DC Conv w/Op Amps RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX1542ETP+T | 功能描述:LCD 驱动器 TFT LCD DC/DC Conv w/Op Amps RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。