- 您现在的位置：买卖IC网 > PDF目录1837 > MAX1541ETL+T (Maxim Integrated Products)IC REG CTRLR DIVIDER PWM 40-TQFN PDF资料下载
参数资料
| 型号： | MAX1541ETL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 36/49页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR DIVIDER PWM 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 620kHz |
| 占空比： | 100% |
| 电源电压： | 2 V ~ 28 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 是 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
Dual Step-Down Controllers with Saturation
Protection, Dynamic Output, and Linear Regulator
Inductor Selection
The switching frequency and inductor operating point
determine the inductor value as follows:
Setting the Current Limit
The minimum current-limit threshold must be great
enough to support the maximum load current when the
L =
V OUT ( V IN - V OUT )
V IN × f SW xI LOAD(MAX) × LIR
current limit is at the minimum tolerance value. The val-
ley of the inductor current occurs at I LOAD(MAX) minus
half the ripple current; therefore:
L =
= 4.65 μ H
? V OUT ( V IN ( MIN ) - V OUT ) ?
For example: I LOAD(MAX) = 4A, V IN = 12V, V OUT2 =
2.5V, f SW = 355kHz, 30% ripple current or LIR = 0.3:
2.5V × (12V - 2.5V)
12V × 3 55 kHz x 4 A × 0 . 3
Find a low-loss inductor with the lowest possible DC
resistance that fits in the allotted dimensions. Ferrite
cores are often the best choice, although powdered
iron is inexpensive and can work well at 200kHz. The
core must be large enough not to saturate at the peak
inductor current (I PEAK ):
I LIM(VAL) > I LOAD(MAX) - ? ?
? 2 V IN ( MIN ) f SW L ?
where I LIM(VAL) equals the minimum valley current-limit
threshold voltage divided by the current-sense resis-
tance (R SENSE ). For the 50mV default setting, the mini-
mum valley current-limit threshold is 40mV.
Connect ILIM_ to V CC for a default 50mV valley current-
limit threshold. In adjustable mode, the valley current-
limit threshold is precisely 1/10th the voltage seen at
ILIM_. For an adjustable threshold, connect a resistive
I PEAK = I LOAD(MAX) ? 1 +
?
?
?
LIR ?
2 ?
divider from REF to analog ground (GND) with ILIM_
connected to the center tap. The external 250mV to 2V
adjustment range corresponds to a 25mV to 200mV
L ( Δ I LOAD(MAX) ) 2 ? ? OUT
? ? ?
? + t OFF(MIN) ?
? ?
? ? ( V IN - V OUT ) × K ?
V SAG =
2 C OUT × V OUT ? ? ? - t OFF(MIN) ?
? ? V IN ? ?
≈ ( Δ I LOAD(MAX) ) 2 L
× V
Most inductor manufacturers provide inductors in stan-
dard values, such as 1.0μH, 1.5μH, 2.2μH, 3.3μH, etc.
Also look for nonstandard values, which can provide a
better compromise in LIR across the input voltage
range. If using a swinging inductor (where the no-load
inductance decreases linearly with increasing current),
evaluate the LIR with properly scaled inductance values.
Transient Response
The inductor ripple current also impacts transient-
response performance, especially at low V IN - V OUT dif-
ferentials. Low inductor values allow the inductor
current to slew faster, replenishing charge removed
from the output filter capacitors by a sudden load step.
The amount of output sag is also a function of the maxi-
mum duty factor, which can be calculated from the on-
time and minimum off-time:
? ? V × K ? ?
V IN ?
?
? ?
where t OFF(MIN) is the minimum off-time (see the
Electrical Characteristics ) and K is from Table 3.
The amount of overshoot during a full-load to no-load tran-
sient due to stored inductor energy can be calculated as:
V SOAR
2 C OUT OUT
valley current-limit threshold. When adjusting the
current limit, use 1% tolerance resistors and a divider
current of approximately 10μA to prevent significant
inaccuracy in the valley current-limit tolerance.
The current-sense method (Figure 14) and magnitude
determine the achievable current-limit accuracy and
power loss (Table 9). Typically, higher current-sense
voltage limits provide tighter accuracy, but also dissi-
pate more power. Most applications employ a valley
current-sense voltage (V LIM(VAL) ) of 50mV to 100mV,
so the sense resistor may be determined by:
R SENSE = V LIM(VAL) / I LIM(VAL)
For the best current-sense accuracy and overcurrent
protection, use a 1% tolerance current-sense resistor
between the inductor and output as shown in Figure
14a. This configuration constantly monitors the inductor
current, allowing accurate valley current-limiting and
inductor-saturation protection.
For low-output-voltage applications that require higher
efficiency, the current-sense resistor can be connected
between the source of the low-side MOSFET (N L_ ) and
power ground (Figure 14b) with CSN_ connected to the
drain of N L_ and CSP_ connected to power ground. In
this configuration, the additional current-sense resis-
tance only dissipates power when N L_ is conducting
current. Inductor-saturation protection must be dis-
abled with this configuration (LSAT = GND) since the
inductor current is only properly sensed when the low-
side MOSFET is turned on.
36
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1542ETP+T | IC DC-DC CONV TFT-LCD 20-TQFN |
| MAX1544ETL+ | IC QUICK-PWM DUAL-PHASE 40-TQFN |
| MAX1545ETL+ | IC QUICK-PWM DUAL-PHASE 40-TQFN |
| MAX1551EZK+T | IC BATT CHRGR LI+ 1CELL SOT23-5 |
| MAX1556ETB/V+T | IC REG BUCK SYNC ADJ 1.2A 10TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1541EVKIT | 制造商:Maxim Integrated Products 功能描述:DUAL STEP-DOWN CONTROLLERS W. SATURATION PROT - Bulk |
| MAX15425EVKIT# | 功能描述:显示开发工具 Eval Kit for the MAX15425 (Intel CPU Controller) RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
| MAX1542ETP | 功能描述:LCD 驱动器 RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX1542ETP+ | 功能描述:LCD 驱动器 TFT LCD DC/DC Conv w/Op Amps RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX1542ETP+T | 功能描述:LCD 驱动器 TFT LCD DC/DC Conv w/Op Amps RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。