- 您现在的位置：买卖IC网 > PDF目录1837 > MAX1541ETL+T (Maxim Integrated Products)IC REG CTRLR DIVIDER PWM 40-TQFN PDF资料下载
参数资料
| 型号： | MAX1541ETL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 30/49页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR DIVIDER PWM 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 620kHz |
| 占空比： | 100% |
| 电源电压： | 2 V ~ 28 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 是 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
Dual Step-Down Controllers with Saturation
Protection, Dynamic Output, and Linear Regulator
Table 6. FBLANK Configuration Table
POWER-GOOD
FAULT PROTECTION
0.9 x
INT REF_
1.1 x
INT REF_
0.7 x
INT REF_
1.16 x
INT REF_
FBLANK
OUT1 FAULT
BLANKING
FORCED-PWM
DURATION (MIN/TYP)
(μs)
INT FB_
ENABLE OVP
V CC
Open
REF
GND
Enabled
Enabled
Enabled
Disabled
120/220
80/140
35/65
80/140
ENABLE UVP
*BLANK
Shutdown and Output Discharge (ON_)
When the output discharge mode is enabled (OVP/UVP
20ms
TIMER
POR
FAULT
LATCH
FAULT
POWER-
GOOD
connected to V CC or left open), and either ON_ is
pulled low or an OVP fault or thermal fault sets the fault
latch (Table 7), the controller discharges each output
through an internal 10 Ω switch connected between
OUT_ and ground. While the output discharges, DL_ is
forced low and the PWM controller is disabled. Once
the output voltage drops below 0.3V, the low-side driver
pulls DL_ high, effectively clamping the output and LX_
*MAIN MAX1541 CONTROLLER (OUT1) ONLY
Figure 9. Power-Good and Fault Protection
ON1 or ON2, or cycling V CC power below 1V. For logic-
level output voltages, connect an external pullup resis-
tor between PGOOD_ and V CC . A 100k Ω resistor works
well in most applications.
Note that the power-good window detectors are com-
pletely independent of the overvoltage and undervolt-
age-protection fault detectors.
Fault Blanking (MAX1541 FBLANK)
The main MAX1541 controller (OUT1) automatically
enters forced-PWM operation during all dynamic output-
voltage transitions (GATE transition detected) in order to
ensure fast, accurate transitions. FBLANK determines
how long the main MAX1541 controller maintains forced-
PWM operation (Table 6—typically 220μs (FBLANK =
V CC ), 140μs (FBLANK = open or GND), or 65μs
(FBLANK = REF).
When fault blanking is enabled (FBLANK = V CC , open,
or REF), the MAX1541 also disables the overvoltage
and undervoltage fault protection for OUT1, and forces
PGOOD1 to a high-impedance state during the transi-
tion period selected by FBLANK (Table 6). This pre-
vents fault protection from latching off the MAX1541
and the PGOOD1 signal from going low when the out-
put voltage change ( Δ V OUT1 ) cannot occur as fast as
the REFIN1 voltage change ( Δ V REFIN1 ).
switching node to ground. The reference remains active
until both output voltages are below 0.3V to provide an
accurate 0.3V discharge threshold.
When OVP/UVP is connected to REF or GND, the con-
troller does not actively discharge either output, and the
DL_ driver remains low until the system reenables the
controller. Under these conditions, the output discharge
rate is determined by the load current and output
capacitance.
The controller detects and latches the discharge-mode
state set by OVP/UVP on startup.
Fault Protection
The MAX1540A/MAX1541 provide over/undervoltage
fault protection (Figure 9). Drive OVP/UVP to enable
and disable fault protection as shown in Table 7. Once
activated, the controller continuously monitors the out-
put for undervoltage and overvoltage fault conditions.
Overvoltage Protection (OVP)
When the output voltage rises above 116% of the nomi-
nal regulation voltage and OVP is enabled (OVP/UVP =
V CC or open), the OVP circuit sets the fault latch, shuts
down both the Quick-PWM controllers, immediately
pulls DH1 and DH2 low, and forces DL1 and DL2 high.
This turns on the synchronous-rectifier MOSFETs with
100% duty, rapidly discharging the output capacitors
and clamping both outputs to ground. Note that imme-
diately latching DL_ high can cause the output voltages
to go slightly negative due to energy stored in the out-
put LC at the instant the OV fault occurs. If the load
30
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1542ETP+T | IC DC-DC CONV TFT-LCD 20-TQFN |
| MAX1544ETL+ | IC QUICK-PWM DUAL-PHASE 40-TQFN |
| MAX1545ETL+ | IC QUICK-PWM DUAL-PHASE 40-TQFN |
| MAX1551EZK+T | IC BATT CHRGR LI+ 1CELL SOT23-5 |
| MAX1556ETB/V+T | IC REG BUCK SYNC ADJ 1.2A 10TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1541EVKIT | 制造商:Maxim Integrated Products 功能描述:DUAL STEP-DOWN CONTROLLERS W. SATURATION PROT - Bulk |
| MAX15425EVKIT# | 功能描述:显示开发工具 Eval Kit for the MAX15425 (Intel CPU Controller) RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
| MAX1542ETP | 功能描述:LCD 驱动器 RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX1542ETP+ | 功能描述:LCD 驱动器 TFT LCD DC/DC Conv w/Op Amps RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX1542ETP+T | 功能描述:LCD 驱动器 TFT LCD DC/DC Conv w/Op Amps RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。