- 您现在的位置：买卖IC网 > PDF目录5055 > MAX17080GTL+ (Maxim Integrated Products)IC CONTROLLER AMD SVI 40-TQFN PDF资料下载
参数资料
| 型号： | MAX17080GTL+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 26/48页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER AMD SVI 40-TQFN |
| 标准包装： | 60 |
| 应用： | 控制器，AMD SVI |
| 输入电压： | 2.7 V ~ 5.5 V |
| 输出数： | 3 |
| 输出电压： | 0.013 V ~ 1.55 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
AMD 2-/3-Output Mobile Serial
VID Controller
V OUT3_PK TARGET3 LOAD3 +
= V
? 6 . 5 mV/A × (I
? I L 3
( V IN 3 ? V OUT 3 ) × V OUT 3
? I L 3 =
where V CS = V CSP - V CSN is the differential current-
sense voltage, and Gm (FBAC) is 2.06mS (max) as
defined in the Electrical Characteristics table.
AC droop is required for stable operation of the
MAX17080. A minimum of 1.5mV/A is recommended.
AC droop must not be disabled.
Core Differential Remote Sense
The MAX17080 controller includes independent differen-
tial, remote-sense inputs for each CPU core to eliminate
the effects of voltage drops along the PCB traces and
through the processor’s power pins. The feedback-sense
(FBDC_) input connects to the remote-sensed output
through the resistance at FBDC_ (R FBDC_ ). The ground-
sense (GNDS_) input connects to an amplifier that adds
an offset directly to the target voltage, effectively
adjusting the output voltage to counteract the voltage
drop in the ground path. Connect the feedback-sense
(FBDC_) R FBDC_ resistor and ground-sense (GNDS_)
input directly to the respective CPU core ’s remote-
sense outputs as shown in Figure 2.
GNDS1 and GNDS2 are dual-function pins. At power-on,
the voltage levels on GNDS1 and GNDS2 configure the
MAX17080 as two independent switching SMPSs, or one
higher current 2-phase SMPS. Keep both GNDS1 and
GNDS2 low during power-up to configure the MAX17080
in separate mode. Connect GNDS1 or GNDS2 to a volt-
age above 0.8V (typ) for combined-mode operation. In
the AMD mobile system, this is automatically done by the
CPU that is plugged into the socket that pulls GNDS1 or
GNDS2 the V DDIO voltage level.
When GNDS1 is pulled high to indicate combined-
mode operation, the remote ground sense is automati-
cally switched to GNDS2. When GNDS2 is pulled high
to indicate combined-mode operation, the remote
ground sense is automatically switched to GNDS1.
GNDS1 and GNDS2 do not dynamically switch in the
real application. It is only switched when one CPU is
removed (e.g., split-core CPU), and another is plugged
in (e.g., combined-core CPU). This should not be done
when the socket is “hot” (i.e., powered).
The MAX17080 checks the GNDS1 and GNDS2 levels
at the time when the internal REFOK signal goes high,
and latches the operating mode information (separate
or combined mode). This latch is cleared by cycling the
SHDN pin.
Core Integrator Amplifier
An internal integrator amplifier forces the DC average of
the FBDC_ voltage to equal the target voltage. This
transconductance amplifier integrates the feedback
voltage and provides a fine adjustment to the regulation
voltage (Figure 3), allowing accurate DC output-voltage
regulation regardless of the output ripple voltage.
The MAX17080 disables the integrator during down-
ward VID transitions done in pulse-skipping mode. The
integrator remains disabled until the transition is com-
pleted (the internal target settles) and the output is in
regulation (edge detected on the error comparator).
The integrator amplifier has the ability to shift the output
voltage by ± 80mV (min). The maximum difference
between transient AC droop and DC droop should not
exceed ± 80mV at the maximum allowed load current to
guarantee proper DC output-voltage accuracy over the
full load conditions.
NB SMPS Feedback Adjustment Amplifiers
NB Steady-State Voltage Positioning (DC Droop)
The NB SMPS has a built-in load-line that is -6.5mV/A.
The output peak voltage (V OUT3_PK+ ) is set to:
)
2
L 3 × V IN 3 × f SW 3
where the target voltage (V TARGET3 ) is defined in the
Nominal Output-Voltage Selection section, f SW3 is the
NB switching frequency, and I LOAD3 is the output load
current of the NB SMPS.
2-Wire Serial Interface (SVC, SVD)
The MAX17080 supports the 2-wire, write-only, serial-
interface bus as defined by the AMD serial VID inter-
face specification. The serial interface is similar to the
high-speed 3.4MHz I 2 C bus, but without the master
mode sequence. The bus consists of a clock line (SVC)
and a data line (SVD). The CPU is the bus master, and
the MAX17080 is the slave. The MAX17080 serial inter-
face works from 100kHz to 3.4MHz. In the AMD mobile
application, the bus runs at 3.4MHz.
The serial interface is active only after PGD_IN goes
high in the startup sequence. The CPU sets the VID
voltage of the three internal DACs and the PSI_L bit
through the serial interface.
During the startup sequence, the SVC and SVD inputs
serve an alternate function to set the 2-bit boot VID for
all three DACs while PWRGD is low.
26
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| GBA49DRMS | CONN EDGECARD 98POS .125 SQ WW |
| X5649S14I-2.7A | IC SUPERVISOR CPU 64K EE 14-SOIC |
| X5649S14I-2.7 | IC SUPERVISOR CPU 64K EE 14-SOIC |
| P1330R-333K | INDUCTOR POWER 33.0UH SMD |
| P1330-333K | INDUCTOR POWER 33.0UH SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17080GTL+ | 功能描述:开关变换器、稳压器与控制器 Integrated Circuits (ICs) Voltage Regulators - Special Purpose - IC CONTROLLER AMD SVI 40-TQFN RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MAX17080GTL+T | 功能描述:开关变换器、稳压器与控制器 Integrated Circuits (ICs) Voltage Regulators - Special Purpose - IC CONTROLLER AMD SVI 40-TQFN RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MAX17081EVKIT+ | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17081EWV+ | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17081EWV+T | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。