- 您现在的位置：买卖IC网 > PDF目录5055 > MAX17080GTL+ (Maxim Integrated Products)IC CONTROLLER AMD SVI 40-TQFN PDF资料下载
参数资料
| 型号： | MAX17080GTL+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 38/48页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER AMD SVI 40-TQFN |
| 标准包装： | 60 |
| 应用： | 控制器，AMD SVI |
| 输入电压： | 2.7 V ~ 5.5 V |
| 输出数： | 3 |
| 输出电压： | 0.013 V ~ 1.55 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页当前第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
AMD 2-/3-Output Mobile Serial
VID Controller
? V
? ? ? V ?
L = ??
? ? OUT ?
? f SW I LOAD ( MAX ) LIR ? ? V IN ?
V IN OUT
?
where I LOAD(MAX) is the maximum current per phase,
and f SW is the switching frequency per phase.
In CPU V CORE converters and other applications where
the output is subject to large load transients, the output
capacitor’s size typically depends on how much ESR is
needed to prevent the output from dipping too low
under a load transient. Ignoring the sag due to finite
capacitance:
Find a low-loss inductor with the lowest possible DC
resistance that fits in the allotted dimensions. If using a
swinging inductor (where the inductance decreases lin-
( R ESR + R PCB ) ≤
V STEP
? I LOAD ( MAX )
early with increasing current), evaluate the LIR with
properly scaled inductance values. For the selected
inductance value, the actual peak-to-peak inductor
ripple current ( ? I INDUCTOR ) is defined by:
In non-CPU applications, the output capacitor’s size
often depends on how much ESR is needed to maintain
an acceptable level of output ripple voltage. The output
ripple voltage of a step-down controller equals the total
( V ? V
? I INDUCTOR = OUT IN OUT
V
V IN f SW L
)
inductor ripple current multiplied by the output capaci-
tor’s ESR. When operating multiphase systems out-of-
phase, the peak inductor currents of each phase are
? I LOAD ( MAX ) ? ? ? I INDUCTOR ?
I PEAK = ? ?+ ? ?
? ?
V IN SW L
R ESR ≤ ?
? V RIPPLE
( ? I LOAD ( MAX ) )
2 V OUT SOAR
Ferrite cores are often the best choice, although pow-
dered iron is inexpensive and can work well at 200kHz.
The core must be large enough not to saturate at the
peak inductor current (I PEAK ):
? η PH ? ? 2 ?
Core Peak Inductor Current Limit (ILIM12)
The MAX17080 overcurrent protection employs a peak
current-sensing algorithm that uses either current-
sense resistors or the inductor’s DCR as the current-
sense element (see the Current Sense section). Since
the controller limits the peak inductor current, the maxi-
mum average load current is less than the peak cur-
rent-limit threshold by an amount equal to half the
inductor ripple current. Therefore, the maximum load
capability is a function of the current-sense resistance,
inductor value, switching frequency, and input-to-out-
put voltage difference. When combined with the output
undervoltage-protection circuit, the system is effectively
protected against excessive overload conditions.
The peak current-limit threshold is set by the voltage
difference between ILIM and REF using an external
resistor-divider:
V CS(PK) = V CSP _ - V CSN _ = 0.052 x (V REF - V ILIM12 )
I LIMIT(PK) = V CS(PK) /R SENSE
where R SENSE is the resistance value of the current-
sense element (inductors’ DCR or current-sense resis-
tor), and I LIMIT(PK) is the desired peak current limit (per
phase). The peak current-limit threshold voltage adjust-
ment range is from 10mV to 50mV.
Core Output Capacitor Selection
The output filter capacitor must have low enough ESR
to meet output ripple and load-transient requirements.
staggered, resulting in lower output ripple voltage
(V RIPPLE ) by reducing the total inductor ripple current.
For nonoverlapping, multiphase operation (V IN ≥ V OUT ),
the maximum ESR to meet the output-ripple-voltage
requirement is:
f
? ? ( V IN ? V OUT ) V OUT ? ?
where f SW is the switching frequency per phase. The
actual capacitance value required relates to the physi-
cal size needed to achieve low ESR, as well as to the
chemistry of the capacitor technology. Thus, the capac-
itor selection is usually limited by ESR and voltage rat-
ing rather than by capacitance value (this is true of
polymer types).
The capacitance value required is determined primarily
by the output transient-response requirements. Low
inductor values allow the inductor current to slew faster,
replenishing charge removed from or added to the out-
put filter capacitors by a sudden load step. Therefore,
the amount of output soar when the load is removed is
a function of the output voltage and inductor value. The
minimum output capacitance required to prevent over-
shoot (V SOAR ) due to stored inductor energy can be
calculated as:
2
L
C OUT ≥
V
When using low-capacity ceramic filter capacitors,
capacitor size is usually determined by the capacity
needed to prevent V SOAR from causing problems during
load transients. Generally, once enough capacitance is
added to meet the overshoot requirement, undershoot at
the rising load edge is no longer a problem.
38
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| GBA49DRMS | CONN EDGECARD 98POS .125 SQ WW |
| X5649S14I-2.7A | IC SUPERVISOR CPU 64K EE 14-SOIC |
| X5649S14I-2.7 | IC SUPERVISOR CPU 64K EE 14-SOIC |
| P1330R-333K | INDUCTOR POWER 33.0UH SMD |
| P1330-333K | INDUCTOR POWER 33.0UH SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17080GTL+ | 功能描述:开关变换器、稳压器与控制器 Integrated Circuits (ICs) Voltage Regulators - Special Purpose - IC CONTROLLER AMD SVI 40-TQFN RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MAX17080GTL+T | 功能描述:开关变换器、稳压器与控制器 Integrated Circuits (ICs) Voltage Regulators - Special Purpose - IC CONTROLLER AMD SVI 40-TQFN RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MAX17081EVKIT+ | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17081EWV+ | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17081EWV+T | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。