- 您现在的位置：买卖IC网 > PDF目录13110 > MAX8550AETI+ (Maxim Integrated Products)IC PWR SUP DDR INTEG 28TQFN PDF资料下载
参数资料
| 型号： | MAX8550AETI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/29页 |
| 文件大小： | 0K |
| 描述： | IC PWR SUP DDR INTEG 28TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 应用： | 控制器，DDR |
| 输入电压： | 2 V ~ 28 V |
| 输出数： | 2 |
| 输出电压： | 1.8V，2.5V，0.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
Detailed Description
The MAX8550A combines a synchronous-buck PWM con-
troller, an LDO linear regulator, and a 10mA reference out-
put buffer. The buck controller drives two external
n-channel MOSFETs to deliver load currents up to 12A
and generate voltages down to 0.7V from a +2V to +28V
input. The LDO linear regulator can sink and source up to
1.5A continuous and 3A peak current with relatively fast
response. These features make the MAX8550/MAX8551
ideally suited for DDR memory applications.
The MAX8550A buck regulator is equipped with a fixed
switching frequency of up to 600kHz using Maxim’s
proprietary constant on-time Quick-PWM architecture.
This control scheme handles wide input/output voltage
ratios with ease, and provides 100ns “instant-on ”
response to load transients, while maintaining high effi-
ciency with relatively constant switching frequency.
The buck controller, LDO, and a reference output
buffer are provided with independent current limits.
Lossless foldback current limit in the buck regulator is
achieved by monitoring the drain-to-source voltage
drop of the low-side FET. The ILIM input is used to
adjust this current limit. Overvoltage protection, if
selected, is achieved by latching the low-side synchro-
nous FET on and the high-side FET off when the output
voltage is over 116% of its set output. It also features
an optional undervoltage protection by latching the
MOSFET drivers to the OFF state during an overcurrent
condition, when the output voltage is lower than 70% of
the regulated output. This helps minimize power dissi-
pation during a short-circuit condition.
The current limit in the LDO and buffered reference out-
put buffer is ±5A and ±32mA, respectively, and neither
have the over- or undervoltage protection. When the
the IC. The current from the AV DD and V DD power
supply must supply the current for the IC and the gate
drive for the MOSFETs. This maximum current can be
estimated as:
I BIAS = I VDD + I AVDD + f SW × ( Q G 1 + Q G 2 )
where I VDD + I AVDD are the quiescent supply currents
into V DD and AV DD , Q G1 and Q G2 are the total gate
charges of MOSFETs Q1 and Q2 (at V GS = 5V) in the
Typical Applications Circuit , and f SW is the switching
frequency.
Free-Running Constant-On-Time PWM
The Quick-PWM control architecture is a pseudo-fixed-
frequency, constant on-time, current-mode regulator
with voltage feed-forward (Figure 1). This architecture
relies on the output filter capacitor’s ESR to act as a
current-sense resistor, so the output ripple voltage pro-
vides the PWM ramp signal. The control algorithm is
simple: the high-side switch on-time is determined
solely by a one-shot whose pulse width is inversely pro-
portional to input voltage and directly proportional to
the output voltage. Another one-shot sets a minimum
off-time of 300ns (typ). The on-time one-shot is trig-
gered if the error comparator is low, the low-side switch
current is below the valley current-limit threshold, and
the minimum off-time one-shot has timed out.
On-Time One-Shot (TON)
The heart of the PWM core is the one-shot that sets the
high-side switch on-time. This fast, low-jitter, adjustable
one-shot includes circuitry that varies the on-time in
response to input and output voltages. The high-side
switch on-time is inversely proportional to the input volt-
age (V IN ) and is proportional to the output voltage:
current limit in either output is reached, the output no
longer regulates the voltage, but regulates the current
to the value of the current limit.
t ON = K ×
( V OUT
+ I LOAD × R DS ( ON ) Q 2
V IN
)
+5V Bias Supply (V DD and AV DD )
The MAX8550A requires an external +5V bias supply in
addition to the input voltage (V IN ). Keeping the bias sup-
ply external to the IC improves the efficiency and elimi-
nates the cost associated with the +5V linear regulator
that would otherwise be needed to supply the PWM cir-
cuit and the gate drivers. If stand-alone capability is
needed, then the +5V supply can be generated with an
external linear regulator such as the MAX1615. V DD ,
AV DD , and IN can be connected together if the input
source is a fixed +4.5V to +5.5V supply.
V DD is the supply input for the buck regulator’s MOSFET
drivers, and AV DD supplies the power for the rest of
where K (the switching period) is set by the TON input
connection (Table 1) and R DS(ON)Q2 is the on-resis-
tance of the synchronous rectifier (Q2) in the Typical
Applications Circuit (Figure 8). This algorithm results in
a nearly constant switching frequency despite the lack
of a fixed-frequency clock generator. The benefits of a
constant switching frequency are twofold:
1) The frequency can be selected to avoid noise-sensi-
tive regions such as the 455kHz IF band.
2) The inductor ripple-current operating point remains
relatively constant, resulting in an easy design
methodology and predictable output voltage ripple.
12
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8632ETI+ | IC PWR SUPPLY DDR 28-TQFN |
| VE-J1B-CZ-B1 | CONVERTER MOD DC/DC 95V 25W |
| ASC15DRAN | CONN EDGECARD 30POS .100 R/A DIP |
| MAX17582GTM+ | IC PWM CTRLR STP-DN DL 48TQFN |
| RMM18DTAS | CONN EDGECARD 36POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8550AETI+ | 功能描述:电压模式 PWM 控制器 Integrated DDR Power Supply Solution RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX8550AETI+T | 功能描述:电压模式 PWM 控制器 Integrated DDR Power Supply Solution RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX8550AETI-T | 功能描述:PMIC 解决方案 RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8550ETI | 功能描述:PMIC 解决方案 RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8550ETI+ | 功能描述:电压模式 PWM 控制器 Integrated DDR Power Supply Solution RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。