- 您现在的位置：买卖IC网 > PDF目录13110 > MAX8550AETI+ (Maxim Integrated Products)IC PWR SUP DDR INTEG 28TQFN PDF资料下载
参数资料
| 型号： | MAX8550AETI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/29页 |
| 文件大小： | 0K |
| 描述： | IC PWR SUP DDR INTEG 28TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 应用： | 控制器，DDR |
| 输入电压： | 2 V ~ 28 V |
| 输出数： | 2 |
| 输出电压： | 1.8V，2.5V，0.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
Pin Description
PIN
1
2
3
4
5
6
7
8
9
10
NAME
TON
OVP/
UVP
REF
ILIM
POK1
POK2
STBY
SS
VTTS
VTTR
FUNCTION
On-Time Selection-Control Input. This four-level logic input sets the nominal DH on-time. Connect to
GND, REF, AV DD , or leave TON unconnected to select the following nominal switching frequencies:
TON = AV DD (200kHz)
TON = OPEN (300kHz)
TON = REF (450kHz)
TON = GND (600kHz)
Overvoltage/Undervoltage-Protection Control Input. This four-level logic input enables or disables the
overvoltage and/or undervoltage protection. The overvoltage limit is 116% of the nominal output
voltage. The undervoltage limit is 70% of the nominal output voltage. Discharge mode is enabled when
OVP is also enabled. Connect the OVP/UVP pin to the following pins for the desired function:
OVP/UVP = AV DD (Enable OVP and discharge mode, enable UVP.)
OVP/UVP = OPEN (Enable OVP and discharge mode, disable UVP.)
OVP/UVP = REF (Disable OVP and discharge mode, enable UVP.)
OVP/UVP = GND (Disable OVP and discharge mode, disable UVP.)
+2.0V Reference Voltage Output. Bypass to GND with a 0.1μF (min) capacitor. REF can supply 50μA
for external loads. Can be used for setting voltage for ILIM. REF turns off when SHDN is low and
OUT < 0.1V.
Valley Current-Limit Threshold Adjustment for Buck Regulator. The current-limit threshold across PGND
and LX is 0.1 times the voltage at ILIM. Connect ILIM to a resistive divider, typically from REF to GND,
to set the current-limit threshold between 25mV and 200mV. This corresponds to a 0.25V to 2V range at
ILIM. Connect ILIM to AV DD to select the 50mV default current-limit threshold. See the Setting the
Current Limit section.
Buck Power-Good Open-Drain Output. POK1 is low when the buck output voltage is more than 10%
above or below the normal regulation point or during soft-start. POK1 is high impedance when the
output is in regulation and the soft-start circuit has terminated. POK1 is low in shutdown.
LDO Power-Good Open-Drain Output. In normal mode, POK2 is low when either VTTR or VTTS is more
than 10% above or below the normal regulation point, which is typically REFIN / 2. In standby mode,
POK2 responds only to the VTTR input. POK2 is low in shutdown, and when V REFIN is less than 0.8V.
Standby. Connect to GND for low-quiescent mode where the VTT output is open circuit. POK2 takes
input from only VTTR in this mode. PWM output can be on or off, depending on the state of SHDN .
Soft-Start Control for VTT. Connect a capacitor (C9 in the Typical Applications Circuit ) from SS to
ground (see the Soft-Start Capacitor Selection section). Leave SS open to disable soft-start.
SS discharges to ground when VTT is off. See the POR, UVLO, and Soft-Start section.
Sensing Pin for Termination Supply Output. Normally connected to VTT pin to allow accurate regulation
to half the REFIN voltage. Connected to a resistive divider from VTT to GND to regulate VTT to higher
than half the REFIN voltage.
Termination Reference Voltage. VTTR tracks V REFIN / 2.
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8632ETI+ | IC PWR SUPPLY DDR 28-TQFN |
| VE-J1B-CZ-B1 | CONVERTER MOD DC/DC 95V 25W |
| ASC15DRAN | CONN EDGECARD 30POS .100 R/A DIP |
| MAX17582GTM+ | IC PWM CTRLR STP-DN DL 48TQFN |
| RMM18DTAS | CONN EDGECARD 36POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8550AETI+ | 功能描述:电压模式 PWM 控制器 Integrated DDR Power Supply Solution RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX8550AETI+T | 功能描述:电压模式 PWM 控制器 Integrated DDR Power Supply Solution RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX8550AETI-T | 功能描述:PMIC 解决方案 RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8550ETI | 功能描述:PMIC 解决方案 RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8550ETI+ | 功能描述:电压模式 PWM 控制器 Integrated DDR Power Supply Solution RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。