- 您现在的位置：买卖IC网 > PDF目录80563 > MC68HC05C5CP (MOTOROLA INC) 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP40 PDF资料下载
参数资料
| 型号： | MC68HC05C5CP |
| 厂商： | MOTOROLA INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP40 |
| 封装： | DIP-40 |
| 文件页数： | 11/58页 |
| 文件大小： | 166K |
| 代理商： | MC68HC05C5CP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页
Page 13
Section 3: Memory
MOTOROLA
MC68HC05C5 Specification Rev. 1.2
address and data buses are configured for normal operation. LATCH is automatically
cleared when LVPI is set. Reset clears this bit.
3.3.1.5
EERC - EEPROM RC Oscillator Control
When this bit is set, the EEPROM section uses the internal RC oscillator instead of the
CPU clock. After setting the EERC bit, delay a time t
RCON to allow the RC oscillator to
stabilize. This bit is readable and writable and should be set by the user when the internal
bus frequency falls below 1.5 MHz. EERC is automatically cleared when LVPI is set.
Reset clears this bit.
3.3.1.6
EEPGM - EEPROM Programming Power Enable
EEPGM must be written to enable (or disable) the EEPGM function. When set, EEPGM
turns on the charge pump and enables the programming (or erasing) power to the
EEPROM array. When clear, this power is switched off. This will enable pulsing of the
programming voltage to be controlled internally. This bit can be read at any time, but can
only be written to if LATCH = 1. If LATCH is not set, then EEPGM cannot be set. LATCH
and EEPGM can not both be set with one write if LATCH is cleared.
EEPGM is
automatically cleared when LVPI is set. EEPGM is automatically cleared when LATCH is
cleared. Reset clears this bit.
3.3.2
PROGRAMMING/ERASING PROCEDURES
To program a byte of EEPROM, set LATCH = CPEN = 1, set ER1 = ER0 = 0, write data
to the desired address and then set EEPGM for a time t
EPGM.
NOTE:
Any bit should be erased before it is programmed. However, if write/
erase cycling is a concern, a procedure can be followed to minimize
the cycling of each bit in each EEPROM byte. Here is the procedure:
If PBEB* = 0, then program the new data over the existing data
without erasing it first
If PBEB*
≠ 0, then erase byte before programming
Where PB = Byte data to be programmed
and EB = Existing EEPROM byte data.
相关PDF资料 |
PDF描述 |
|---|---|
| MB89475PFV | 8-BIT, 12.5 MHz, MICROCONTROLLER, PQFP48 |
| MAH28151FXXXX | 1 CHANNEL(S), 64K bps, SERIAL COMM CONTROLLER, CQFP68 |
| MPC8245LZU300D | 32-BIT, 300 MHz, RISC PROCESSOR, PBGA352 |
| MPC8250AZUMHBB | 32-BIT, 266 MHz, RISC PROCESSOR, PBGA480 |
| MPC859DSLZP66 | 32-BIT, 66 MHz, RISC PROCESSOR, PBGA357 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC68HC05C8 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:PROGRAMMING REFRERENCE GUIDE |
| MC68HC05C8A | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:Microcontrollers |
| MC68HC05C8ACFN | 制造商:Motorola Inc 功能描述:MicroController, 8-Bit, 44 Pin, Plastic, PLCC |
| MC68HC05C9 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:TECHNICAL DATA |
| MC68HC05C9A | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。