- 您现在的位置：买卖IC网 > PDF目录80563 > MC68HC05C5CP (MOTOROLA INC) 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP40 PDF资料下载
参数资料
| 型号： | MC68HC05C5CP |
| 厂商： | MOTOROLA INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP40 |
| 封装： | DIP-40 |
| 文件页数： | 58/58页 |
| 文件大小： | 166K |
| 代理商： | MC68HC05C5CP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页当前第58页
Page 3
Section 1: Introduction
MOTOROLA
MC68HC05C5 Specification Rev. 1.2
NOTE:
Negative true signals like RESET and IRQ will be denoted with either an
asterisk or an overline.
1.4
SIGNAL DESCRIPTION
1.4.1
V
DD
AND V
SS
Power is supplied to the microcontroller using these two pins. V
DD
is the positive supply,
and V
SS
is ground.
1.4.2
PE
PE is the Program Enable for the EEPROM. This pin has a very weak internal pullup. If
this pin is held at a logic "1" level or left not connected, the EEPROM can be programmed
and erased. If this pin is held at a logic "0" level, EEPROM programming and erasing is
disabled. The pullup will not be able to pull the pin high if any circuit is connected to PE.
1.4.3
IRQ
This pin has a mask option that provides two different choices of interrupt triggering
sensitivity. The IRQ pin contains an internal Schmitt trigger as part of its input to improve
noise immunity. Refer to 4.5 INTERRUPTS for more detail.
1.4.4
OSC1 AND OSC2
These pins provide control input for an on-chip clock oscillator circuit. A crystal, a ceramic
resonator, a resistor/capacitor combination, or an external signal connects to these pins
providing a system clock. A mask option selects either a crystal/ceramic resonator or a
resistor/capacitor as the frequency determining element. The oscillator frequency is two
times the internal bus rate.
1.4.5
RESET
This active low pin is used to reset the MCU to a known start-up state by pulling RESET
low. The RESET pin contains an internal Schmitt trigger as part of its input to improve
noise immunity.
1.4.6
TCAP
This pin controls the input capture feature for the on-chip programmable timer. The TCAP
pin contains an internal Schmitt trigger as part of its input to improve noise immunity.
1.4.7
PA0-PA7
These eight I/O lines comprise port A. The state of any pin is software programmable and
all port A lines are configured as input during power-on or reset. Refer to 5.5 INPUT/
OUTPUT PROGRAMMING for a detailed description of I/O programming.
相关PDF资料 |
PDF描述 |
|---|---|
| MB89475PFV | 8-BIT, 12.5 MHz, MICROCONTROLLER, PQFP48 |
| MAH28151FXXXX | 1 CHANNEL(S), 64K bps, SERIAL COMM CONTROLLER, CQFP68 |
| MPC8245LZU300D | 32-BIT, 300 MHz, RISC PROCESSOR, PBGA352 |
| MPC8250AZUMHBB | 32-BIT, 266 MHz, RISC PROCESSOR, PBGA480 |
| MPC859DSLZP66 | 32-BIT, 66 MHz, RISC PROCESSOR, PBGA357 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC68HC05C8 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:PROGRAMMING REFRERENCE GUIDE |
| MC68HC05C8A | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:Microcontrollers |
| MC68HC05C8ACFN | 制造商:Motorola Inc 功能描述:MicroController, 8-Bit, 44 Pin, Plastic, PLCC |
| MC68HC05C9 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:TECHNICAL DATA |
| MC68HC05C9A | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。