- 您现在的位置：买卖IC网 > PDF目录240332 > MC68HC11F1VPU2 (MOTOROLA INC) Technical Summary 8-Bit Microcontroller PDF资料下载
参数资料
| 型号： | MC68HC11F1VPU2 |
| 厂商： | MOTOROLA INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | Technical Summary 8-Bit Microcontroller |
| 中文描述： | 8-BIT, EEPROM, 2 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | 14 X 14 MM, 1.40 MM HEIGHT, PLASTIC, LQFP-80 |
| 文件页数： | 5/163页 |
| 文件大小： | 711K |
| 代理商： | MC68HC11F1VPU2 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页
MOTOROLA
SERIAL PERIPHERAL INTERFACE
MC68HC11F1
8-4
TECHNICAL DATA
8.3.1 Master In Slave Out
MISO is one of two unidirectional serial data signals. It is an input to a master device
and an output from a slave device. The MISO line of a slave device is placed in the
high-impedance state if the slave device is not selected.
8.3.2 Master Out Slave In
The MOSI line is the second of the two unidirectional serial data signals. It is an output
from a master device and an input to a slave device. The master device places data
on the MOSI line a half-cycle before the clock edge that the slave device uses to latch
the data.
8.3.3 Serial Clock
SCK, an input to a slave device, is generated by the master device and synchronizes
data movement in and out of the device through the MOSI and MISO lines. Master and
slave devices are capable of exchanging a byte of information during a sequence of
eight clock cycles.
There are four possible timing relationships that can be chosen by using control bits
CPOL and CPHA in the serial peripheral control register (SPCR). Both master and
slave devices must operate with the same timing. The SPI clock rate select bits,
SPR[1:0], in the SPCR of the master device, select the clock rate. In a slave device,
SPR[1:0] have no effect on the operation of the SPI.
8.3.4 Slave Select
The slave select (SS) input of a slave device must be externally asserted before a
master device can exchange data with the slave device. SS must be low before data
transactions and must stay low for the duration of the transaction.
The SS line of the master must be held high. If it goes low, a mode fault error flag
(MODF) is set in the serial peripheral status register (SPSR). To disable the mode fault
circuit, write a one in bit 5 of the port D data direction register. This sets the SS pin to
act as a general-purpose output rather than the dedicated input to the slave select cir-
cuit, thus inhibiting the mode fault flag. The other three lines are dedicated to the SPI
whenever the serial peripheral interface is on.
The state of the master and slave CPHA bits affects the operation of SS. CPHA set-
tings should be identical for master and slave. When CPHA = 0, the shift clock is the
OR of SS with SCK. In this clock phase mode, SS must go high between successive
characters in an SPI message. When CPHA = 1, SS can be left low between succes-
sive SPI characters. In cases where there is only one SPI slave MCU, its SS line can
be tied to Vss as long as only CPHA = 1 clock mode is used.
8.4 SPI System Errors
Two system errors can be detected by the SPI system. The first type of error arises in
a multiple-master system when more than one SPI device simultaneously tries to be
a master. This error is called a mode fault. The second type of error, write collision,
indicates that an attempt was made to write data to the SPDR while a transfer was in
progress.
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC11F1VPU3 | Technical Summary 8-Bit Microcontroller |
| MC68HC11F1VPU4 | Technical Summary 8-Bit Microcontroller |
| MI-QC211-MWY | Military DC-DC Power Supplies |
| MI-QC211-MXY | Military DC-DC Power Supplies |
| MI-QC211-MYY | Military DC-DC Power Supplies |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC68HC11F1VPU3 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
| MC68HC11F1VPU4 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
| MC68HC11FC0 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
| MC68HC11FC0CFU4 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
| MC68HC11FC0CFU5 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
发布紧急采购，3分钟左右您将得到回复。