参数资料
| 型号： | NCP5331FTR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 24/36页 |
| 文件大小： | 0K |
| 描述： | IC CTLR PWM 2PH W/DRVRS 32-LQFP |
| 产品变化通告： | Product Obsolescence 05/Oct/2010 |
| 标准包装： | 1 |
| 应用： | 控制器，AMD Athlon? |
| 输入电压： | 9 V ~ 14 V |
| 输出数： | 2 |
| 输出电压： | 5V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-LQFP |
| 供应商设备封装： | 32-LQFP（7x7） |
| 包装： | 剪切带 (CT) |
| 其它名称： | NCP5331FTR2GOSCT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
NCP5331
(VIN * VCORE) @ VCORE
( a @ IO,MAX @ VIN @ fSW)
D IO,MAX
D VO,MAX
14. The CS REF sense point should be equidistant
between the output inductors to equalize the PCB
resistance added to the current sense paths. This
will insure acceptable current sharing. Also, route
the CS REF connection away from noisy traces such
as the SWNODEs and GATE traces. If noise from
the SWNODEs or GATE signals capacitively
couples to the CSREF trace the external ramps
will be very noisy and voltage jitter will result.
15. Ideally, the SWNODEs are exactly the same shape
and the current sense points (connections to R S1
and R S2 ) are made at identical locations to equalize
the PCB resistance added to the current sense paths.
This will help to insure acceptable current sharing.
16. Place the 1 m F ceramic capacitors, C P1 and C P2 ,
close to the drains of the MOSFETs Q1 and Q2,
respectively.
17. If snubbers are used, they must be placed very
close to their associated MOSFETs and
SWNODE. The connections to the snubber
components should be as short as possible.
Design Procedure
1. Output Capacitor Selection
The output capacitors filter the current from the output
inductor and provide a low impedance for transient load
current changes. Typically, microprocessor applications
will require both bulk (electrolytic, tantalum) and low
impedance, high frequency (ceramic) types of capacitors.
The bulk capacitors provide “hold up” during transient
loading. The low impedance capacitors reduce steady?state
ripple and bypass the bulk capacitance when the output
current changes very quickly. The microprocessor
manufacturers usually specify a minimum number of
ceramic capacitors. The designer must determine the
number of bulk capacitors.
Choose the number of bulk output capacitors to meet the
peak transient requirements. The following formula can be
used to provide a starting point for the minimum number of
bulk capacitors (N OUT,MIN ).
(1)
NOUT,MIN + ESR per capacitor @
In reality, both the ESR and ESL of the bulk capacitors
determine the voltage change during a load transient
according to
D VO,MAX + ( D IO,MAX D t) @ ESL ) D IO,MAX @ ESR (2)
Unfortunately, capacitor manufacturers do not specify the
ESL of their components and the inductance added by the
PCB traces is highly dependent on the layout and routing.
Therefore, it is necessary to start a design with slightly more
2. Output Inductor Selection
The output inductor may be the most critical component
in the converter because it will directly effect the choice of
other components and dictate both the steady?state and
transient performance of the converter. When selecting an
inductor the designer must consider factors such as dc
current, peak current, output voltage ripple, core material,
magnetic saturation, temperature, physical size, and cost
(usually the primary concern).
In general, the output inductance value should be as low
and physically small as possible to provide the best transient
response and minimum cost. If a large inductance value is
used, the converter will not respond quickly to rapid changes
in the load current. On the other hand, too low an inductance
value will result in very large ripple currents in the power
components (MOSFETs, capacitors, etc) resulting in
increased dissipation and lower converter efficiency. Also,
increased ripple currents will force the designer to use
higher rated MOSFETs, oversize the thermal solution, and
use more, higher rated input and output capacitors ? the
converter cost will be adversely effected.
One method of calculating an output inductor value is to
size the inductor to produce a specified maximum ripple
current in the inductor. Lower ripple currents will result in
less core and MOSFET losses and higher converter
efficiency. Equation 3 may be used to calculate the
minimum inductor value to produce a given maximum
ripple current ( α ) per phase. The inductor value calculated
by this equation is a minimum because values less than this
will produce more ripple current than desired. Conversely,
higher inductor values will result in less than the maximum
ripple current.
(3)
LoMIN +
α is the ripple current as a percentage of the maximum
output current per phase ( α = 0.15 for ± 15%, α = 0.25 for
± 25%, etc). If the minimum inductor value is used, the
inductor current will swing ± α % about its value at the center
(half the dc output current for a two?phase converter).
Therefore, for a two?phase converter, the inductor must be
designed or selected such that it will not saturate with a peak
current of (1 + α ) ? I O,MAX /2.
The maximum inductor value is limited by the transient
response of the converter. If the converter is to have a fast
transient response then the inductor should be made as small
as possible. If the inductor is too large its current will change
too slowly, the output voltage will droop excessively, more
bulk capacitors will be required, and the converter cost will
be increased. For a given inductor value, its interesting to
determine the time required to increase or decrease the
current.
than the minimum number of bulk capacitors and perform
transient testing or careful modeling/simulation to
determine the final number of bulk capacitors.
http://onsemi.com
24
相关PDF资料 |
PDF描述 |
|---|---|
| NCP5332ADW | IC CTLR BUCK 2PH DRVR/DAC 28SOIC |
| NCP5378MNR2G | IC CTLR 1PH SYNC BUCK 32QFN |
| NCP5380AMNR2G | IC CTLR SYNC BUCK SGL 32QFN |
| NCP5381AMNR2G | IC BUCK CTLR 2/3/4PHASE 40-QFN |
| NCP5381MNR2G | IC CTLR BUCK 2/3/4PHASE 40-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP5332A | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Two-Phase Buck Controller with Integrated Gate Drivers and 5-Bit DAC |
| NCP5332A/D | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Two-Phase Buck Controller with Integrated Gate Drivers and 5-Bit DAC |
| NCP5332ADW | 功能描述:DC/DC 开关控制器 2 Phase Buck w/Gate RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP5332ADWR2 | 功能描述:DC/DC 开关控制器 2 Phase Buck w/Gate RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP5338MNR2G | 制造商:ON Semiconductor 功能描述:INTEGRATED DRIVER AND MOS - Tape and Reel 制造商:ON Semiconductor 功能描述:INTEGRATED DRIVER AND MOS - Cut TR (SOS) 制造商:ON Semiconductor 功能描述:REEL / INTEGRATED DRIVER AND MOS 制造商:ON Semiconductor 功能描述:Integrated Driver and MOSFET |
发布紧急采购，3分钟左右您将得到回复。