- 您现在的位置：买卖IC网 > PDF目录12014 > P89V51RB2BBC,557 (NXP Semiconductors)IC 80C51 MCU 1024 RAM 44TQFP PDF资料下载
参数资料
| 型号： | P89V51RB2BBC,557 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 14/80页 |
| 文件大小： | 0K |
| 描述： | IC 80C51 MCU 1024 RAM 44TQFP |
| 产品培训模块： | Migrating from 8/16-Bit MCUs to 32-Bit ARMs |
| 标准包装： | 800 |
| 系列： | 89V |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 40MHz |
| 连通性： | SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 16KB（16K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 振荡器型： | 内部 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 44-TQFP |
| 包装： | 托盘 |
| 配用： | 622-1017-ND - BOARD 44-ZIF PLCC SOCKET |
| 其它名称： | 935277723557 P89V51RB2BBC P89V51RB2BBC-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
P89V51RB2_RC2_RD2_5
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 05 — 12 November 2009
21 of 80
NXP Semiconductors
P89V51RB2/RC2/RD2
8-bit microcontrollers with 80C51 core
A chip-erase operation can be performed using a commercially available parallel
programer. This operation will erase the contents of this boot block and it will be
necessary for the user to reprogram this boot block (block 1) with the NXP-provided
ISP/IAP code in order to use the ISP or IAP capabilities of this device. Go to
http://www.nxp.com/support for questions or to obtain the hex le for this device.
6.3.3 ISP
ISP is performed without removing the microcontroller from the system. The ISP facility
consists of a series of internal hardware resources coupled with internal rmware to
facilitate remote programming of the P89V51RB2/RC2/RD2 through the serial port. This
rmware is provided by NXP and embedded within each P89V51RB2/RC2/RD2 device.
The NXP ISP facility has made in-circuit programming in an embedded application
possible with a minimum of additional expense in components and circuit board area. The
ISP function uses ve pins (VDD, VSS, TXD, RXD, and RST). Only a small connector
needs to be available to interface your application to an external circuit in order to use this
feature.
6.3.4 Using ISP
The ISP feature allows for a wide range of baud rates to be used in your application,
independent of the oscillator frequency. It is also adaptable to a wide range of oscillator
frequencies. This is accomplished by measuring the bit-time of a single bit in a received
character. This information is then used to program the baud rate in terms of timer counts
based on the oscillator frequency. The ISP feature requires that an initial character (an
uppercase U) be sent to the P89V51RB2/RC2/RD2 to establish the baud rate. The ISP
rmware provides auto-echo of received characters. Once baud rate initialization has
been performed, the ISP rmware will only accept Intel Hex-type records. Intel Hex
records consist of ASCII characters used to represent hexadecimal values and are
summarized below:
:NNAAAARRDD..DDCC<crlf>
In the Intel Hex record, the ‘NN’ represents the number of data bytes in the record. The
P89V51RB2/RC2/RD2 will accept up to 32 data bytes. The ‘AAAA’ string represents the
address of the rst byte in the record. If there are zero bytes in the record, this eld is often
set to 0000. The ‘RR’ string indicates the record type. A record type of ‘00’ is a data
record. A record type of ‘01’ indicates the end-of-le mark. In this application, additional
record types will be added to indicate either commands or data for the ISP facility.
The maximum number of data bytes in a record is limited to 32 (decimal). ISP commands
are summarized in Table 12. As a record is received by the P89V51RB2/RC2/RD2, the
information in the record is stored internally and a checksum calculation is performed. The
operation indicated by the record type is not performed until the entire record has been
received. Should an error occur in the checksum, the P89V51RB2/RC2/RD2 will send an
‘X’ out the serial port indicating a checksum error. If the checksum calculation is found to
match the checksum in the record, then the command will be executed. In most cases,
successful reception of the record will be indicated by transmitting a ‘.’ character out the
serial port.
相关PDF资料 |
PDF描述 |
|---|---|
| VJ1825A223JBCAT4X | CAP CER 0.022UF 200V 5% NP0 1825 |
| VJ1825A223KBCAT4X | CAP CER 0.022UF 200V NP0 1825 |
| VJ2225A562JBAAT4X | CAP CER 5600PF 50V 5% NP0 2225 |
| VJ2225A562JBBAT4X | CAP CER 5600PF 100V 5% NP0 2225 |
| VJ2225A562JBCAT4X | CAP CER 5600PF 200V 5% NP0 2225 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P89V51RB2FA | 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 16K FLASH PLCC44 |
| P89V51RB2FA,529 | 功能描述:8位微控制器 -MCU 80C51 16K FL / 512 R RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89V51RB2FA529 | 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 40MHZ LCC-44 |
| P89V51RB2FN | 制造商:NXP Semiconductors 功能描述:IC MCU 8BIT 80C51 16K FLASH DIP40 制造商:NXP Semiconductors 功能描述:IC, MCU 8BIT 80C51 16K FLASH, DIP40 |
| P89V51RB2FN,112 | 功能描述:8位微控制器 -MCU 80C51 16K FL / 512 R RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。