- 您现在的位置：买卖IC网 > PDF目录1965 > PIC18LF96J65-I/PT (Microchip Technology)IC PIC MCU FLASH 48KX16 100TQFP PDF资料下载
参数资料
| 型号： | PIC18LF96J65-I/PT |
| 厂商： | Microchip Technology |
| 文件页数： | 22/131页 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 48KX16 100TQFP |
| 标准包装： | 90 |
| 系列： | PIC® 18F |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 41.667MHz |
| 连通性： | EBI/EMI，以太网，I²C，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 70 |
| 程序存储器容量： | 96KB（48K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 3808 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2 V ~ 3.6 V |
| 数据转换器： | A/D 16x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 100-TQFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页
PIC18F97J60 FAMILY
DS39762F-page 118
2011 Microchip Technology Inc.
8.3
Wait States
While it may be assumed that external memory devices
will operate at the microcontroller clock rate, this is
often not the case. In fact, many devices require longer
times to write or retrieve data than the time allowed by
the execution of table read or table write operations.
To compensate for this, the external memory bus can
be configured to add a fixed delay to each table opera-
tion using the bus. Wait states are enabled by setting
the WAIT Configuration bit. When enabled, the amount
of delay is set by the WAIT<1:0> bits (MEMCON<5:4>).
The delay is based on multiples of microcontroller
instruction cycle time and is added following the
instruction cycle when the table operation is executed.
The range is from no delay to 3 TCY (default value).
8.4
Port Pin Weak Pull-ups
With the exception of the upper address lines,
A<19:16>, the pins associated with the external mem-
ory bus are equipped with weak pull-ups. The pull-ups
are controlled by bits located at LATA<7:6> and
PORTA<7>. They are named RDPU, REPU and RJPU
and control pull-ups on PORTD, PORTE and PORTJ,
respectively. Setting one of these bits enables the
corresponding pull-ups for that port. All pull-ups are
disabled by default on all device Resets.
In Extended Microcontroller mode, the port pull-ups
can be useful in preserving the memory state on the
external bus while the bus is temporarily disabled
(EBDIS = 1).
8.5
Program Memory Modes and the
External Memory Bus
The PIC18F97J60 family of devices is capable of
operating in one of two program memory modes, using
combinations of on-chip and external program memory.
The functions of the multiplexed port pins depend on
the program memory mode selected, as well as the
setting of the EBDIS bit.
In Microcontroller Mode, the bus is not active and the
pins have their port functions only. Writes to the
MEMCOM register are not permitted. The Reset value
of EBDIS (‘0’) is ignored and the EMB pins behave as
I/O ports.
In Extended Microcontroller Mode, the external
program memory bus shares I/O port functions on the
pins. When the device is fetching, or doing table
read/table write operations on the external program
memory space, the pins will have the external bus
function.
If the device is fetching and accessing internal program
memory locations only, the EBDIS control bit will change
the pins from external memory to I/O port functions.
When EBDIS = 0, the pins function as the external bus.
When EBDIS = 1, the pins function as I/O ports.
If the device fetches or accesses external memory
while EBDIS = 1, the pins will switch to the external
bus. If the EBDIS bit is set by a program executing from
external memory, the action of setting the bit will be
delayed until the program branches into the internal
memory. At that time, the pins will change from external
bus to I/O ports.
If the device is executing out of internal memory when
EBDIS = 0, the memory bus address/data and control
pins will not be active. They will go to a state where the
active address/data pins are tri-state; the CE, OE,
WRH, WRL, UB and LB signals are ‘1’, and ALE and
BA0 are ‘0’. Note that only those pins associated with
the current address width are forced to tri-state; the
other pins continue to function as I/O. In the case of
16-bit address width, for example, only AD<15:0>
(PORTD and PORTE) are affected; A<19:16>
(PORTH<3:0>) continue to function as I/O.
In all external memory modes, the bus takes priority
over any other peripherals that may share pins with it.
This includes the Parallel Slave Port and serial
communication modules, which would otherwise take
priority over the I/O port.
8.6
16-Bit Data Width Modes
In 16-Bit Data Width mode, the external memory
interface can be connected to external memories in
three different configurations:
16-Bit Byte Write
16-Bit Word Write
16-Bit Byte Select
The configuration to be used is determined by
the WM<1:0> bits in the MEMCON register
(MEMCON<1:0>). These three different configurations
allow the designer maximum flexibility in using both
8-bit and 16-bit devices with 16-bit data.
For all 16-Bit Data Width modes, the Address Latch
Enable (ALE) pin indicates that the address bits,
AD<15:0>, are available in the external memory inter-
face bus. Following the address latch, the Output
Enable signal (OE) will enable both bytes of program
memory at once to form a 16-bit instruction word. The
Chip Enable signal (CE) is active at any time that the
microcontroller accesses external memory, whether
reading or writing. It is inactive (asserted high)
whenever the device is in Sleep mode.
In Byte Select mode, JEDEC standard Flash memories
will require BA0 for the byte address line and one I/O
line to select between Byte and Word mode. The other
16-Bit Data Width modes do not need BA0. JEDEC
standard, static RAM memories will use the UB or LB
signals for byte selection.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC24F16KL401-I/P | IC MCU 16BIT 16KB FLASH 20-PDIP |
| PIC24FJ128GA010-I/PF | IC PIC MCU FLASH 128KB 100TQFP |
| PIC24FJ256GA110-I/PF | IC PIC MCU FLASH 256K 100TQFP |
| PIC24FJ256GB110-I/PF | IC PIC MCU FLASH 256K 100TQFP |
| PIC24FJ64GA004-E/ML | IC PIC MCU FLASH 64K 44-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC1-R68-JT | 制造商:RCD 制造商全称:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-JTQ | 制造商:RCD 制造商全称:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-JTW | 制造商:RCD 制造商全称:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-KT | 制造商:RCD 制造商全称:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-KTQ | 制造商:RCD 制造商全称:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
发布紧急采购，3分钟左右您将得到回复。