- 您现在的位置：买卖IC网 > PDF目录1965 > PIC18LF96J65-I/PT (Microchip Technology)IC PIC MCU FLASH 48KX16 100TQFP PDF资料下载
参数资料
| 型号： | PIC18LF96J65-I/PT |
| 厂商： | Microchip Technology |
| 文件页数： | 73/131页 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 48KX16 100TQFP |
| 标准包装： | 90 |
| 系列： | PIC® 18F |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 41.667MHz |
| 连通性： | EBI/EMI，以太网，I²C，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 70 |
| 程序存储器容量： | 96KB（48K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 3808 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2 V ~ 3.6 V |
| 数据转换器： | A/D 16x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 100-TQFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页当前第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页
PIC18F97J60 FAMILY
DS39762F-page 46
2011 Microchip Technology Inc.
2.4.1
CONSIDERATIONS FOR CERAMIC
CAPACITORS
In recent years, large value, low-voltage, surface-mount
ceramic capacitors have become very cost effective in
sizes up to a few tens of microfarad. The low-ESR, small
physical size and other properties make ceramic
capacitors very attractive in many types of applications.
Ceramic capacitors are suitable for use with the
VDDCORE voltage regulator of this microcontroller.
However, some care is needed in selecting the capac-
itor to ensure that it maintains sufficient capacitance
over the intended operating range of the application.
Typical low-cost, 10 F ceramic capacitors are available
in X5R, X7R and Y5V dielectric ratings (other types are
also available, but are less common). The initial toler-
ance specifications for these types of capacitors are
often specified as ±10% to ±20% (X5R and X7R), or
-20%/+80% (Y5V). However, the effective capacitance
that these capacitors provide in an application circuit will
also vary based on additional factors, such as the
applied DC bias voltage and the temperature. The total
in-circuit tolerance is, therefore, much wider than the
initial tolerance specification.
The X5R and X7R capacitors typically exhibit satisfac-
tory temperature stability (ex: ±15% over a wide
temperature range, but consult the manufacturer's data
sheets for exact specifications). However, Y5V capaci-
tors typically have extreme temperature tolerance
specifications of +22%/-82%. Due to the extreme
temperature tolerance, a 10 F nominal rated Y5V type
capacitor may not deliver enough total capacitance to
meet minimum VDDCORE voltage regulator stability and
transient response requirements. Therefore, Y5V
capacitors are not recommended for use with the
VDDCORE regulator if the application must operate over
a wide temperature range.
In addition to temperature tolerance, the effective
capacitance of large value ceramic capacitors can vary
substantially, based on the amount of DC voltage
applied to the capacitor. This effect can be very signifi-
cant, but is often overlooked or is not always
documented.
A typical DC bias voltage vs. capacitance graph for
X7R type and Y5V type capacitors is shown in
FIGURE 2-4:
DC BIAS VOLTAGE vs.
CAPACITANCE
CHARACTERISTICS
When selecting a ceramic capacitor to be used with the
VDDCORE voltage regulator, it is suggested to select a
high-voltage rating, so that the operating voltage is a
small percentage of the maximum rated capacitor volt-
age. For example, choose a ceramic capacitor rated at
16V for the 2.5V VDDCORE voltage. Suggested
capacitors are shown in Table 2-1.
2.5
ICSP Pins
The PGC and PGD pins are used for In-Circuit Serial
Programming (ICSP) and debugging purposes. It
is recommended to keep the trace length between the
ICSP connector and the ICSP pins on the device as
short as possible. If the ICSP connector is expected to
experience an ESD event, a series resistor is recom-
mended, with the value in the range of a few tens of
ohms, not to exceed 100.
Pull-up resistors, series diodes, and capacitors on the
PGC and PGD pins are not recommended as they will
interfere with the programmer/debugger communica-
tions to the device. If such discrete components are an
application requirement, they should be removed from
the circuit during programming and debugging. Alter-
natively, refer to the AC/DC characteristics and timing
requirements information in the respective device
Flash programming specification for information on
capacitive loading limits, and pin input voltage high
(VIH) and input low (VIL) requirements.
For device emulation, ensure that the “Communication
Channel Select” (i.e., PGCx/PGDx pins), programmed
into the device, matches the physical connections for
the ICSP to the Microchip debugger/emulator tool.
For
more
information
on
available
Microchip
development tools connection requirements, refer to
.
-80
-70
-60
-50
-40
-30
-20
-10
0
10
5
1011121314
15
16
17
DC Bias Voltage (VDC)
Capacit
a
nce
Change
(%)
012
34
67
89
16V Capacitor
10V Capacitor
6.3V Capacitor
相关PDF资料 |
PDF描述 |
|---|---|
| PIC24F16KL401-I/P | IC MCU 16BIT 16KB FLASH 20-PDIP |
| PIC24FJ128GA010-I/PF | IC PIC MCU FLASH 128KB 100TQFP |
| PIC24FJ256GA110-I/PF | IC PIC MCU FLASH 256K 100TQFP |
| PIC24FJ256GB110-I/PF | IC PIC MCU FLASH 256K 100TQFP |
| PIC24FJ64GA004-E/ML | IC PIC MCU FLASH 64K 44-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC1-R68-JT | 制造商:RCD 制造商全称:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-JTQ | 制造商:RCD 制造商全称:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-JTW | 制造商:RCD 制造商全称:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-KT | 制造商:RCD 制造商全称:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-KTQ | 制造商:RCD 制造商全称:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
发布紧急采购，3分钟左右您将得到回复。