- 您现在的位置：买卖IC网 > PDF目录11830 > SC16C850IET,157 (NXP Semiconductors)IC UART SINGLE W/FIFO 36-TFBGA PDF资料下载
参数资料
| 型号： | SC16C850IET,157 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 11/55页 |
| 文件大小： | 0K |
| 描述： | IC UART SINGLE W/FIFO 36-TFBGA |
| 标准包装： | 2,450 |
| 特点： | 可编程 |
| 通道数： | 1，UART |
| FIFO's： | 128 字节 |
| 规程： | RS485 |
| 电源电压： | 2.5 V ~ 3.3 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-TFBGA |
| 供应商设备封装： | 36-TFBGA（3.5x3.5） |
| 包装： | 托盘 |
| 其它名称： | 935284685157 SC16C850IET SC16C850IET-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
SC16C850
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 11 November 2010
19 of 55
NXP Semiconductors
SC16C850
2.5 to 3.3 V UART with 128-byte FIFOs and IrDA encoder/decoder
6.13 RS-485 features
6.13.1 Auto RS-485 RTS control
Normally the RTS pin is controlled by MCR[1], or if hardware flow control is enabled, the
logic state of the RTS pin is controlled by the hardware flow control circuitry. AFCR2[4] will
take the precedence over the other two modes; once this bit is set, the transmitter will
control the state of the RTS pin. The transmitter automatically asserts the RTS pin
(logic 0) once the host writes data to the transmit FIFO, and de-asserts RTS pin (logic 1)
once the last bit of the data has been transmitted.
To use the auto RS-485 RTS mode the software would have to disable the hardware
flow control function.
6.13.2 RS-485 RTS inversion
AFCR2[5] reverses the polarity of the RTS pin if the UART is in auto RS-485 RTS mode.
When the transmitter has data to be sent it will de-asserts the RTS pin (logic 1), and when
the last bit of the data has been sent out the transmitter asserts the RTS pin (logic 0).
6.13.3 Auto 9-bit mode (RS-485)
AFCR2[0] is used to enable the 9-bit mode (Multi-drop or RS-485 mode). In this mode of
operation, a ‘master’ station transmits an address character followed by data characters
for the addressed ‘slave’ stations. The slave stations examine the received data and
interrupt the controller if the received character is an address character (parity bit = 1).
To use the automatic 9-bit mode, the software would have to disable the hardware and
software flow control functions.
6.13.3.1
Normal Multi-drop mode
The 9-bit Mode in AFCR2[0] is enabled, but not Special Character Detect (EFR[5]). The
receiver is set to Force Parity 0 (LCR[5:3] = 111) in order to detect address bytes.
With the receiver initially disabled, it ignores all the data bytes (parity bit = 0) until an
address byte is received (parity bit = 1). This address byte will cause the UART to set the
parity error. The UART will generate a line status interrupt (IER[2] must be set to ‘1’ at this
time), and at the same time puts this address byte in the RX FIFO. After the controller
examines the byte it must make a decision whether or not to enable the receiver; it should
enable the receiver if the address byte addresses its ID address, and must not enable the
receiver if the address byte does not address its ID address.
If the controller enables the receiver, the receiver will receive the subsequent data until
being disabled by the controller after the controller has received a complete message
from the ‘master’ station. If the controller does not disable the receiver after receiving a
message from the ‘master’ station, the receiver will generate a parity error upon receiving
another address byte. The controller then determines if the address byte addresses its ID
address, if it is not, the controller then can disable the receiver. If the address byte
addresses the ‘slave’ ID address, the controller takes no further action, and the receiver
will receive the subsequent data.
相关PDF资料 |
PDF描述 |
|---|---|
| SC16IS750IBS,128 | IC UART I2C/SPI 24-HVQFN |
| SC16IS741IPW,128 | IC UART 16TSSOP |
| SC16IS740IPW,128 | IC UART SINGLE W/FIFO 16-TSSOP |
| SC16IS750IBS,157 | IC UART 64BYTE 24HVQFN |
| SC16C550BIBS,157 | IC UART SOT617-1 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC16C850IET-G | 功能描述:UART 接口集成电路 16C 2.5-5V 5MBPS UART 128BFIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C850IET-S | 功能描述:UART 接口集成电路 16C 2.5-5V 5MBPS UART 128BFIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C850L | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:1.8 V single UART, 5 Mbit/s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode parallel bus interface |
| SC16C850LIB,128 | 制造商:NXP Semiconductors 功能描述: |
| SC16C850LIB,151 | 制造商:NXP Semiconductors 功能描述: |
发布紧急采购，3分钟左右您将得到回复。