- 您现在的位置：买卖IC网 > PDF目录11830 > SC16C850IET,157 (NXP Semiconductors)IC UART SINGLE W/FIFO 36-TFBGA PDF资料下载
参数资料
| 型号： | SC16C850IET,157 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 4/55页 |
| 文件大小： | 0K |
| 描述： | IC UART SINGLE W/FIFO 36-TFBGA |
| 标准包装： | 2,450 |
| 特点： | 可编程 |
| 通道数： | 1，UART |
| FIFO's： | 128 字节 |
| 规程： | RS485 |
| 电源电压： | 2.5 V ~ 3.3 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-TFBGA |
| 供应商设备封装： | 36-TFBGA（3.5x3.5） |
| 包装： | 托盘 |
| 其它名称： | 935284685157 SC16C850IET SC16C850IET-ND |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
SC16C850
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 11 November 2010
12 of 55
NXP Semiconductors
SC16C850
2.5 to 3.3 V UART with 128-byte FIFOs and IrDA encoder/decoder
6.5 Hardware flow control
When automatic hardware flow control is enabled, the SC16C850 monitors the CTS pin
for a remote buffer overflow indication and controls the RTS pin for local buffer overflows.
Automatic hardware flow control is selected by setting EFR[6] (RTS) and EFR[7] (CTS) to
a logic 1. If CTS transitions from a logic 0 to a logic 1 indicating a flow control request,
ISR[5] will be set to a logic 1 (if enabled via IER[7:6]), and the SC16C850 will suspend TX
transmissions as soon as the stop bit of the character in process is shifted out.
Transmission is resumed after the CTS input returns to a logic 0, indicating more data
may be sent.
When AFCR1[2] is set to logic 1 then the function of CTS pin is mapped to the DSR pin,
and the function of RTS is mapped to DTR pin. DSR and DTR pins will behave as
described above for CTS and RTS.
With the automatic hardware flow control function enabled, an interrupt is generated when
the receive FIFO reaches the programmed trigger level. The RTS (or DTR) pin will not be
forced to a logic 1 (RTS off), until the receive FIFO reaches the next trigger level.
However, the RTS (or DTR) pin will return to a logic 0 after the receive buffer (FIFO) is
unloaded to the next trigger level below the programmed trigger level. Under the above
described conditions, the SC16C850 will continue to accept data until the receive FIFO is
full.
When the TXINTLVL, RXINTLVL, FLWCNTH and FLWCNTL in the ‘first extra feature
register set’ are all zeroes, the hardware and software flow control trigger levels are set by
FCR[7:4]; see Table 6.
When the TXINTLVL, RXINTLVL, FLWCNTH or FLWCNTL in the ‘first extra feature
register set’ contain any value other than 0x00, the hardware and software flow control
trigger levels are set by FLWCNTH and FLWCNTL. The content in FLWCNTH determines
how many bytes are in the receive FIFO before RTS (or DTR) is de-asserted or Xoff is
sent. The content in FLWCNTL determines how many bytes are in the receive FIFO
before RTS (or DTR) is asserted, or Xon is sent.
In 128-byte FIFO mode, hardware and software flow control trigger levels can be set to
any value between 1 and 128 in granularity of 1. The value of FLWCNTH should always
be greater than FLWCNTL. The UART does not check for this condition automatically, and
if this condition is not met, spurious operation of the device might occur. When using
FLWCNTH and FLWCNTL, these registers must be initialized to proper values before
hardware or software flow control is enabled via the EFR register.
6.6 Software flow control
When software flow control is enabled, the SC16C850 compares one or two sequentially
received data characters with the programmed Xon or Xoff character value(s). If the
received character(s) match the programmed Xoff values, the SC16C850 will halt
transmission (TX) as soon as the current character(s) has completed transmission. When
a match occurs, ISR bit 4 will be set (if enabled via IER[5]) and the interrupt output pin (if
receive interrupt is enabled) will be activated. Following a suspension due to a match of
the Xoff characters’ values, the SC16C850 will monitor the receive data stream for a
match to the Xon1/Xon2 character value(s). If a match is found, the SC16C850 will
resume operation and clear the flags (ISR[4]).
相关PDF资料 |
PDF描述 |
|---|---|
| SC16IS750IBS,128 | IC UART I2C/SPI 24-HVQFN |
| SC16IS741IPW,128 | IC UART 16TSSOP |
| SC16IS740IPW,128 | IC UART SINGLE W/FIFO 16-TSSOP |
| SC16IS750IBS,157 | IC UART 64BYTE 24HVQFN |
| SC16C550BIBS,157 | IC UART SOT617-1 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC16C850IET-G | 功能描述:UART 接口集成电路 16C 2.5-5V 5MBPS UART 128BFIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C850IET-S | 功能描述:UART 接口集成电路 16C 2.5-5V 5MBPS UART 128BFIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C850L | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:1.8 V single UART, 5 Mbit/s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode parallel bus interface |
| SC16C850LIB,128 | 制造商:NXP Semiconductors 功能描述: |
| SC16C850LIB,151 | 制造商:NXP Semiconductors 功能描述: |
发布紧急采购，3分钟左右您将得到回复。