- 您现在的位置：买卖IC网 > PDF目录16215 > SI3225DC0-EVB (Silicon Laboratories Inc)DAUGHTER CARD W/SI3200 INTERFACE PDF资料下载
参数资料
| 型号： | SI3225DC0-EVB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 111/112页 |
| 文件大小： | 0K |
| 描述： | DAUGHTER CARD W/SI3200 INTERFACE |
| 标准包装： | 1 |
| 系列： | ProSLIC® |
| 主要目的： | 接口，模拟前端（AFE） |
| 已用 IC / 零件： | Si3225 |
| 已供物品： | 板，CD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页当前第111页第112页
Si3220/25 Si3200/02
98
Rev. 1.3
Not
Recommended
fo
r N
ew
D
esi
gn
s
Figure 64. SLIC Diagnostic Filter Structure
3.32.4. Measurement Tools
8-Bit monitor A/D converter. This 8-bit A/D
converter monitors all dc and low-frequency voltage
and current data from TIP to ground and RING to
ground. Two additional values, TIP – RING and
TIP + RING, are calculated and stored in on-chip
registers to analyze metallic and longitudinal effects.
The A/D operates at an 800 Hz update rate to allow
measurement bandwidth from dc to 400 Hz. A dual-
range capability allows high-voltage/high-current
measurement in the high range but can also
measure lower voltages and currents with a tighter
resolution.
Programmable bandpass filter. A bandpass filter
discriminates certain frequency ranges, such as
ringing frequencies and 50 Hz/60 Hz induction, from
nearby or crossed power leads.
SLIC diagnostics filter. Several post-processing
filter blocks monitor peak dc and ac characteristics of
the Monitor A/D converter outputs and values
derived from these outputs. Setting the SDIAG bit in
the DIAG register enables the filters. There are
separate filters for each channel, and their control is
independent. These filters require DSP processing,
which is available only when voice band processing
is not being performed. If an off-hook or ring trip
condition is detected while the SDIAG bit is set, the
bit is cleared, and the diagnostic information is not
processed.
The following parameters can be selected as inputs
to the diagnostic block by setting the SDIAG bits in
the DIAG register to values 0–7 corresponding to the
order below:
VTIP = voltage on the TIP lead
VRI NG = voltage on the RING lead
VLOOP =VTIP-VRING = metallic (loop) voltage
VLONG =(VTIP+VRING)/2 = longitudinal voltage
ILOOP =ITIP-IRING = metallic (loop) current
ILONG =(ITIP+IRING)/2 = longitudinal current
VRING, EXT = ringing voltage when using an external
ringing source (Si3225 only)
IRING,EXT = ringing current when using an external
ringing source (Si3225 only)
The SLIC diagnostic capability consists of a peak detect
block and two filter blocks, one for dc and one for ac.
The topology is illustrated in Figure 64.
The peak detect filter block reports the magnitude of the
largest positive or negative value without sign. The dc
filter block consists of a single pole IIR low-pass filter
with a coefficient held in the DIAGDCCO RAM location.
The filter output is read from the DIAGDC RAM location.
The ac filter block consists of a full-wave rectifier
followed by a single-pole IIR low-pass filter with a
coefficient held in the DIAGACCO RAM location. The
peak value is read from the DIAGPK RAM location. The
peak value is cleared and the filters are flushed on the
0-1 transition of the SDIAG bit and when the input
source changes. The user can write 0 to the DIAGPK
RAM location to get peak information for a specific time
interval.
16-bit audio A/D converter. The A/D converter
portion of the audio codec is made available for
processing test data received back through the
transmit audio path. The audio path offers a 2.5 V
peak voltage measurement capability and a coarse
attenuation stage for scenarios where the incoming
signal amplitude must be attenuated by as much as
3 dB to bring it into the allowable input range without
clipping.
VTIP
VRING
VLOOP
VLONG
ILOOP
ILONG
VRING,EXT
IRING,EXT
LPF
PEAK
DETECT
FULL WAVE
RECTIFY
LPF
DIAGAC
DIAGDC
DIAGPK
DIAGACCO
DIAGDCCO
相关PDF资料 |
PDF描述 |
|---|---|
| SEK220M400ST | CAP ALUM 22UF 400V 20% RADIAL |
| CP2201EK | KIT EVAL FOR CP2201 ETH CTRLR |
| PM1210-820J-RC | INDUCTOR 82UH 5% 1210 SMD |
| H3WWH-6036G | IDC CABLE - HPL60H/AE60G/HPL60H |
| UPS2C471MRD | CAP ALUM 470UF 160V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI3225DCX-EVB | 功能描述:子卡和OEM板 Si3225 Daughter Card RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| Si3225-FQ | 功能描述:电信线路管理 IC Dual-Channel SLIC/ codec RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3225-FQR | 制造商:Silicon Laboratories Inc 功能描述: |
| Si3225-G-FQ | 功能描述:电信线路管理 IC Dual-Channel SLIC codec RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3225-G-FQR | 功能描述:电信线路管理 IC Dual-CH SLIC/codec Ext Ringing Support RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。