- 您现在的位置：买卖IC网 > PDF目录16215 > SI3225DC0-EVB (Silicon Laboratories Inc)DAUGHTER CARD W/SI3200 INTERFACE PDF资料下载
参数资料
| 型号： | SI3225DC0-EVB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 50/112页 |
| 文件大小： | 0K |
| 描述： | DAUGHTER CARD W/SI3200 INTERFACE |
| 标准包装： | 1 |
| 系列： | ProSLIC® |
| 主要目的： | 接口，模拟前端（AFE） |
| 已用 IC / 零件： | Si3225 |
| 已供物品： | 板，CD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页当前第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页
Si3220/25 Si3200/02
42
Rev. 1.3
Not
Recommended
fo
r N
ew
D
esi
gn
s
3.9. Automatic Dual Battery Switching
The Dual ProSLIC chipsets provide the ability to switch
between several user-provided battery supplies to aid
thermal management. Two specific scenarios where
this method may be required follow:
Ringing to off-hook state transition (Si3220):
During the on-hook operating state, the Dual
ProSLIC chipset must operate from the ringing
battery supply to provide the desired ringing signal
when required. Once an off-hook condition is
detected, the Dual ProSLIC chipset must transition
to the lower battery supply (typically –24 V) to
reduce power dissipation during the active state. The
low current consumed by the Dual ProSLIC chipset
during the on-hook state results in very little power
dissipation while being powered from the ringing
battery supply, which can have an amplitude as high
as –100 V depending on the desired ringing
amplitude.
On-hook to off-hook state, short loop feed
(Si3225): When sourcing both long and short loop
lengths, the Dual ProSLIC chipset can automatically
switch from the typical –48 V off-hook battery supply
to a lower off-hook battery supply (e.g., –24 V) to
reduce the total off-hook power dissipation. The Dual
ProSLIC chipset continuously monitors the TIP-
RING voltage and selects the lowest battery voltage
required to power the loop when transitioning from
the on-hook to the off-hook state, thus assuring the
lowest power dissipation.
The BATSELa and BATSELb pins switch between the
two battery voltages based on the operating state and
the TIP-RING voltage. Figure 19 illustrates the chip
connections required to implement an automatic dual
battery switching scheme. When BATSEL is pulled
LOW, the desired channel is powered from the VBLO
supply. When BATSEL is pulled HIGH, the VBHI source
supplies power to the desired channel.
The BATSEL pins for both channels are controlled using
the BATSEL bit of the RLYCON register and can be
programmed to automatically switch to the lower battery
supply (VBLO) when the off-hook TIP-RING voltage is
low enough to allow proper operation from the lower
supply. When using the Si3220, this mode should
always be enabled to
allow seamless switching
between the ringing and off-hook states. The same
switching scheme is used with the Si3225 to reduce
power by switching to a lower off-hook battery when
sourcing a short loop.
Automatic battery selection should be disabled before
using the manual battery select control bit (BSEL bit,
Register 5—RLYCON,
bit 5).
Contact
Silicon
Laboratories
for
information
on
how
to
disable
automatic battery selection.
Two thresholds are provided to enable battery switching
with hysteresis. The BATHTH RAM location specifies
the threshold at which the Dual ProSLIC device
switches from the low battery (VBLO) to the high battery
(VBHI) due to an off-hook-to-on-hook transition. The
BATLTH RAM location specifies the threshold at which
the Si3220/Si3225 switches from VBHI to VBLO due to a
transition from the on-hook or ringing state to the off-
hook state or because the overhead during active Off-
Hook mode is sufficient to feed the subscriber loop
using a lower battery voltage.
The low-pass filter coefficient is calculated using the
following equation and is entered into the BATLPF RAM
location:
BATLPF = [(2
f x 4096)/800] x 23
Where f = the desired cutoff frequency of the filter
The programmable range of the filter is from 0h (blocks
all signals) to 4000h (unfiltered). A typical value of
10 Hz (0A10h) is sufficient to filter out any unwanted ac
artifacts while allowing the dc information to pass
through the filter.
Table 23 provides the register and RAM locations used
for programming the battery switching functions.
相关PDF资料 |
PDF描述 |
|---|---|
| SEK220M400ST | CAP ALUM 22UF 400V 20% RADIAL |
| CP2201EK | KIT EVAL FOR CP2201 ETH CTRLR |
| PM1210-820J-RC | INDUCTOR 82UH 5% 1210 SMD |
| H3WWH-6036G | IDC CABLE - HPL60H/AE60G/HPL60H |
| UPS2C471MRD | CAP ALUM 470UF 160V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI3225DCX-EVB | 功能描述:子卡和OEM板 Si3225 Daughter Card RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| Si3225-FQ | 功能描述:电信线路管理 IC Dual-Channel SLIC/ codec RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3225-FQR | 制造商:Silicon Laboratories Inc 功能描述: |
| Si3225-G-FQ | 功能描述:电信线路管理 IC Dual-Channel SLIC codec RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3225-G-FQR | 功能描述:电信线路管理 IC Dual-CH SLIC/codec Ext Ringing Support RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。