收藏本站
参数资料
型号： SPD6729QCE
厂商： INTEL CORP
元件分类： 总线控制器
英文描述： PCMCIA BUS CONTROLLER, PQFP208
封装： MQFP-208
文件页数： 28/116页
文件大小： 1442K
代理商： SPD6729QCE
PCI-to-PC Card (PCMCIA) Controller — PD6729
Datasheet
19
RDY/-IREQ
Ready / Interrupt Request: In Memory
Card Interface mode, this input indicates to
the PD6729 that the card is either ready or
busy. In I/O Card Interface mode, this input
indicates a card interrupt request.
95
170
1
I-PU
2 or 3
–
-WAIT
Wait: This input indicates a request by the
card to the PD6729 to halt the cycle in
progress until this signal is deactivated.
111
186
1
I-PU
2 or 3
–
-CD[2:1]
Card Detect: These inputs indicate to the
PD6729 the presence of a card in the
socket. They are internally pulled high to
the voltage of the +5V power pin.
126, 66
202, 142
2
I-PU
1
–
-CE[2:1]
Card Enable: These outputs are driven
low by the PD6729 during card access
cycles to control byte/word card access.
-CE1 enables even-numbered address
bytes, and -CE2 enables odd-numbered
address bytes. When configured for 8-bit
cards, only -CE1 is active and A0 is used
to indicate access of odd- or even-
numbered bytes.
79, 75
154, 151
2
TO
2 or 3
2 mA
RESET
Card Reset: This output is low for normal
operation and goes high to reset the card.
To prevent reset glitches to a card, this
signal is high-impedance unless a card is
seated in the socket, card power is applied,
and the card’s interface signals are
enabled.
109
184
1
TO
2 or 3
2 mA
BVD2/-SPKR/
-LED
Battery Voltage Detect 2 / Speaker /
LED: In Memory Card Interface mode, this
input serves as the BVD2 (battery warning
status) input. In I/O Card Interface mode,
this input can be configured as a card’s -
SPKR binary audio input. For ATA or non-
ATA (SFF-68) disk-drive support, this input
can also be configured as a drive-status
LED input.
116
192
1
I-PU
2 or 3
–
BVD1/
-STSCHG/-RI
Battery Voltage Detect 1 / Status
Change / Ring Indicate: In Memory Card
Interface mode, this input serves as the
BVD1 (battery-dead status) input. In I/O
Card Interface mode, this input is the -
STSCHG input, which indicates to the
PD6729 that the card’s internal status has
changed. If bit 7 of the Interrupt and
General Control register is set to a ‘1’, this
pin serves as the ring indicate input for
wakeup-on-ring system power
management support.
118
194
1
I-PU
2 or 3
–
Table 2.
Socket Interface Pins (Sheet 2 of 3)
Pin Name1
Description2
Pin Number
Qty.
I/O
Pwr.
Drive
Socket A
Socket B
NOTES:
1. To differentiate the sockets, all socket-specific pins have either A_ or B_ prepended to the pin names indicated. For example,
A_A[25:0] and B_A[25:0] are the independent address buses to the sockets.
2. When a socket is configured as an ATA drive interface, socket interface pin functions change. See “ATA Mode Operation” on
page 91.
相关PDF资料
PDF描述
SPEAR-09-B042 1 CHANNEL(S), 100M bps, I2C BUS CONTROLLER, PBGA289
SPEAR300-2 32-BIT, FLASH, 333 MHz, RISC MICROCONTROLLER, PBGA289
SPL505YC264ATT PROC SPECIFIC CLOCK GENERATOR, PDSO64
SPL505YC264BT 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO64
SPL505YC264BT 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO64
相关代理商/技术参数
参数描述
SPD6730QCB 制造商:Rochester Electronics LLC 功能描述:- Bulk
SPD6832QCB 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Intel 功能描述:
SPD73 制造商:未知厂家 制造商全称:未知厂家 功能描述:Shielded Surface Mount Inductors
SPD73-103M 功能描述:固定电感器 10uH 20% .067ohm Shield Choke SMT Pwr RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
SPD73-103MTR 功能描述:固定电感器 10 UH 20% RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*