- 您现在的位置：买卖IC网 > PDF目录373750 > TZA3015HW (NXP SEMICONDUCTORS) 30 Mbit/s to 3.2 Gbit/s A-rate 4-bit fibre optic transceiver PDF资料下载
参数资料
| 型号： | TZA3015HW |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 数字传输电路 |
| 英文描述： | 30 Mbit/s to 3.2 Gbit/s A-rate 4-bit fibre optic transceiver |
| 中文描述： | TRANSCEIVER, PQFP100 |
| 封装： | 14 X 14 MM, 1 MM HEIGHT, SOT-638-1, HTQFP-100 |
| 文件页数： | 63/67页 |
| 文件大小： | 352K |
| 代理商： | TZA3015HW |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页当前第63页第64页第65页第66页第67页
2003 Dec 16
63
Philips Semiconductors
Preliminary specification
30 Mbit/s to 3.2 Gbit/s A-rate
4-bit fibre optic transceiver
TZA3015HW
SOLDERING
Introduction to soldering surface mount packages
Thistextgivesaverybriefinsighttoacomplextechnology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering can still be used for
certainsurfacemountICs,butitisnotsuitableforfinepitch
SMDs. In these situations reflow soldering is
recommended.
Reflow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Driven by legislation and environmental forces the
worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending
on heating method.
Typical reflow peak temperatures range from
215 to 270
°
C depending on solder paste material. The
top-surface temperature of the packages should
preferably be kept:
below 225
°
C (SnPb process) or below 245
°
C (Pb-free
process)
– for all BGA, HTSSON-T and SSOP-T packages
– for packages with a thickness 2.5 mm
– for packages with a thickness < 2.5 mm and a
volume
≥
350 mm
3
so called thick/large packages.
below 240
°
C (SnPb process) or below 260
°
C (Pb-free
process) for packages with a thickness < 2.5 mm and a
volume < 350 mm
3
so called small/thin packages.
Moisture sensitivity precautions, as indicated on packing,
must be respected at all times.
Wave soldering
Conventional single wave soldering is not recommended
forsurfacemountdevices(SMDs)orprinted-circuitboards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is
preferred
to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
Forpackageswithleadsonfoursides,thefootprintmust
be placed at a 45
°
angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time of the leads in the wave ranges from
3 to 4 seconds at 250
°
C or 265
°
C, depending on solder
material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°
C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°
C.
相关PDF资料 |
PDF描述 |
|---|---|
| Z00607DA | SENSITIVE GATE TRIACS |
| Z00607DA1BA2 | SENSITIVE GATE TRIACS |
| Z00607MA | Fuses, 20A 250V CERAMIC |
| Z0100A | surface mount silicon Zener diodes |
| Z0110A | surface mount silicon Zener diodes |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TZA3017HW | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:30 Mbits/s up to 3.2 Gbits/s A-rate fibre optic transmitter |
| TZA3019 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:2.5 Gbits/s dual postamplifier with level detectors and 2 x 2 switch |
| TZA3019AHT | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:2.5 Gbits/s dual postamplifier with level detectors and 2 x 2 switch |
| TZA3019AV | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:2.5 Gbits/s dual postamplifier with level detectors and 2 x 2 switch |
| TZA3019AVH | 制造商:未知厂家 制造商全称:未知厂家 功能描述:APPLICATION SPECIFIC AMPLIFIER|DUAL|LLCC|32PIN|PLASTIC |
发布紧急采购，3分钟左右您将得到回复。