参数资料
| 型号： | W25Q80BVSSIG |
| 厂商： | Winbond Electronics |
| 文件页数： | 48/75页 |
| 文件大小： | 0K |
| 描述： | IC FLASH 8MBIT 8SOIC |
| 标准包装： | 90 |
| 系列： | SpiFlash® |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | FLASH |
| 存储容量： | 8M（1M x 8） |
| 速度： | 104MHz |
| 接口： | SPI 串行 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.209"，5.30mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
| 其它名称： | Q4816329 T1015683 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页当前第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页
W25Q80BV
6.2.30
Release Power-down / Device ID (ABh)
The Release from Power-down / Device ID instruction is a multi-purpose instruction. It can be used to
release the device from the power-down state, or obtain the devices electronic identification (ID) number.
To release the device from the power-down state, the instruction is issued by driving the /CS pin low,
shifting the instruction code “ABh” and driving /CS high as shown in figure 28a. Release from power-
down will take the time duration of t RES1 (See AC Characteristics) before the device will resume normal
operation and other instructions are accepted. The /CS pin must remain high during the t RES1 time
duration.
When used only to obtain the Device ID while not in the power-down state, the instruction is initiated by
driving the /CS pin low and shifting the instruction code “ABh” followed by 3 -dummy bytes. The Device ID
bits are then shifted out on the falling edge of CLK with most significant bit (MSB) first as shown in figure
28a. The Device ID values for the W25Q80BV is listed in Manufacturer and Device Identification table.
The Device ID can be read continuously. The instruction is completed by driving /CS high.
When used to release the device from the power-down state and obtain the Device ID, the instruction is
the same as previously described, and shown in figure 28b, except that after /CS is driven high it must
remain high for a time duration of t RES2 (See AC Characteristics). After this time duration the device will
resume normal operation and other instructions will be accepted. If the Release from Power-down /
Device ID instruction is issued while an Erase, Program or Write cycle is in process (when BUSY equals
1) the instruction is ignored and will not have any effects on the current cycle.
/CS
tRES1
Mode 3
0
1
2
3
4
5
6
7
Mode 3
CLK
Mode 0
Mode 0
Instruction (ABh)
DI
(IO 0 )
Power-down current
Figure 28a. Release Power-down Instruction Sequence
- 48 -
Stand-by current
相关PDF资料 |
PDF描述 |
|---|---|
| M1A3P600-FGG256 | IC FPGA 1KB FLASH 600K 256-FBGA |
| HMM43DRYI | CONN EDGECARD 86POS DIP .156 SLD |
| M1A3P600-FG256 | IC FPGA 1KB FLASH 600K 256-FBGA |
| RCB70DHBT | CONN EDGECARD 140PS R/A .050 DIP |
| A3P600-FG256 | IC FPGA 1KB FLASH 600K 256-FBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W25Q80BVSSIG TR | 制造商:Winbond Electronics Corp 功能描述:SPIFLASH, 8M-BIT, 4KB UNIFORM 制造商:Winbond Electronics Corp 功能描述:IC FLASH 8MBIT 104MHZ 8SOIC |
| W25Q80BVSSIG/REELS | 制造商:Winbond Electronics Corp 功能描述: |
| W25Q80BVSSIG-T | 制造商:Winbond Electronics 功能描述:8MB SPI FLASH |
| W25Q80BVSSIP | 制造商:WINBOND 制造商全称:Winbond 功能描述:8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q80BVZPAG | 制造商:WINBOND 制造商全称:Winbond 功能描述:8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
发布紧急采购，3分钟左右您将得到回复。