收藏本站
参数资料
型号： WJLXT971ALE.A4SE000
厂商： CORTINA SYSTEMS INC
元件分类： 网络接口
英文描述： DATACOM, ETHERNET TRANSCEIVER, PQFP64
封装： LEAD FREE, LQFP-64
文件页数： 34/116页
文件大小： 1172K
代理商： WJLXT971ALE.A4SE000
LXT971A 3.3V Dual-Speed Fast Ethernet Transceiver
24
Datasheet
Document #: 249414
Revision #: 002
Rev. Date: August 7, 2002
bit 26.11 through software control. Setting Register bit 26.11 = 1 through the MDC/MDIO
interface sets the MII pins (RXD[0:3], RX_DV, RX_CLK, RX_ER, COL, CRS, and TX_CLK) to a
higher drive strength.
3.2.3
Configuration Management Interface
The LXT971A provides both an MDIO interface and a Hardware Control Interface for device
configuration and management.
3.2.3.1
MDIO Management Interface
The LXT971A supports the IEEE 802.3 MII Management Interface also known as the
Management Data Input/Output (MDIO) Interface. This interface allows upper-layer devices to
monitor and control the state of the LXT971A. The MDIO interface consists of a physical
connection, a specific protocol that runs across the connection, and an internal set of addressable
registers.
Some registers are required and their functions are defined by the IEEE 802.3 standard. The
LXT971A also supports additional registers for expanded functionality. The LXT971A supports
multiple internal registers, each of which is 16 bits wide. Specific register bits are referenced using
an “X.Y” notation, where X is the register number (0-31) and Y is the bit number (0-15).
The physical interface consists of a data line (MDIO) and clock line (MDC). Operation of this
interface is controlled by the MDDIS input pin. When MDDIS is High, the MDIO read and write
operations are disabled and the Hardware Control Interface provides primary configuration control.
When MDDIS is Low, the MDIO port is enabled for both read and write operations and the
Hardware Control Interface is not used.
3.2.3.1.1 MDIO Addressing
The protocol allows one controller to communicate with multiple LXT971A chips. Pins
ADDR<4:0> determine the chip address.
3.2.3.1.2 MDIO Frame Structure
The physical interface consists of a data line (MDIO) and clock line (MDC). The frame structure is
shown in Figures 4 and 5 (read and write). MDIO Interface timing is shown in Table 38 on
page 69.
Figure 4. Management Interface Read Frame Structure
MDC
MDIO
(Read)
32 "1"s
0110
Preamble
ST
Op Code
PHY Address
Turn
Around
Z0
A4
A3
A0
R4
R3
R0
Register Address
D15
D14
D1
Data
Write
Read
D15
D14
D1
D0
Idle
High Z
相关PDF资料
PDF描述
WJLXT971ALE.A4SE001 DATACOM, ETHERNET TRANSCEIVER, PQFP64
WJLXT971ALC.A4 DATACOM, ETHERNET TRANSCEIVER, PQFP64
WJLXT971ALE.A4 DATACOM, ETHERNET TRANSCEIVER, PQFP64
WJLXT971ALC.A4 DATACOM, ETHERNET TRANSCEIVER, PQFP64
WJLXT971ALE.A4 DATACOM, ETHERNET TRANSCEIVER, PQFP64
相关代理商/技术参数
参数描述
WJLXT971CA4 制造商:Intel 功能描述:
WJLXT972ALC.A4 功能描述:IC TRANS 3.3V ETHERNET 64-LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件
WJLXT972ALC.A4 S E001 制造商:Intel 功能描述:PHY 1-CH 10Mbps/100Mbps 64-Pin LQFP T/R
WJLXT972ALC.A4-857341 功能描述:TXRX ETH 10/100 SGL PORT 64-LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS422，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 产品目录页面:1402 (CN2011-ZH PDF)
WJLXT972ALC.A4-857345 功能描述:TXRX ETH 10/100 SGL PORT 64-LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1 系列:- 类型:线路收发器 驱动器/接收器数:5/3 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC 包装:Digi-Reel® 产品目录页面:918 (CN2011-ZH PDF) 其它名称:296-25096-6
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*