参数资料
| 型号： | XC2S400E-6FGG456C |
| 厂商： | Xilinx Inc |
| 文件页数： | 28/108页 |
| 文件大小： | 0K |
| 描述： | IC SPARTAN-IIE FPGA 400K 456FBGA |
| 产品变化通告： | FPGA Family Discontinuation 18/Apr/2011 |
| 标准包装： | 60 |
| 系列： | Spartan®-IIE |
| LAB/CLB数： | 2400 |
| 逻辑元件/单元数： | 10800 |
| RAM 位总计： | 163840 |
| 输入/输出数： | 329 |
| 门数： | 400000 |
| 电源电压： | 1.71 V ~ 1.89 V |
| 安装类型： | 表面贴装 |
| 工作温度： | 0°C ~ 85°C |
| 封装/外壳： | 456-BBGA |
| 供应商设备封装： | 456-FBGA |
| 其它名称： | 122-1327 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页
26
DS077-2 (v3.0) August 9, 2013
Product Specification
Spartan-IIE FPGA Family: Functional Description
R
— OBSOLETE — OBSOLETE — OBSOLETE — OBSOLETE —
Master Serial Mode
In Master Serial mode, the CCLK output of the FPGA drives
a Xilinx PROM, which feeds a serial stream of configuration
data to the FPGA’s DIN input. Figure 19 shows a Master
Serial FPGA configuring a Slave Serial FPGA from a
PROM. A Spartan-IIE device in Master Serial mode should
be connected as shown for the device on the left side. Mas-
ter Serial mode is selected by a <00x> on the mode pins
(M0, M1, M2). The PROM RESET pin is driven by INIT, and
the CE input is driven by DONE. For more information on
serial PROMs, see the Xilinx Configuration PROM data
sheets at www.xilinx.com.
The interface is identical to the slave serial mode except
that an oscillator internal to the FPGA is used to generate
the configuration clock (CCLK). Any of a number of different
frequencies ranging from 4 to 60 MHz can be set using the
ConfigRate option in the Xilinx development software.
When selecting a CCLK frequency, ensure that the serial
PROM and any daisy-chained FPGAs are fast enough to
support the clock rate. On power-up, while the first 60 bytes
of the configuration data are being loaded, the CCLK fre-
quency is always 2.5 MHz. This frequency is used until the
ConfigRate bits, part of the configuration file, have been
loaded into the FPGA, at which point the frequency
changes to the selected ConfigRate. Unless a different fre-
quency is specified in the design, the default ConfigRate is
4 MHz. The frequency of the CCLK signal created by the
internal oscillator has a variance of +45%, –30% from the
specified value.
The FPGA accepts one bit of configuration data on each ris-
ing CCLK edge. After the FPGA has been loaded, the data
for the next device in a daisy-chain is presented on the
DOUT pin after the rising CCLK edge. The timing for Master
Serial mode is shown in Figure 25, page 49.
Slave Parallel Mode (SelectMAP)
The Slave Parallel mode, also known as SelectMAP, is the
fastest configuration option. Byte-wide data is written into
the FPGA on the D0-D7 pins. Note that D0 is the MSB of
each byte for configuration. A BUSY flag is provided for con-
trolling the flow of data at a clock frequency above 50 MHz.
shows
the
connections
for
two
Spartan-IIE devices using the Slave Parallel mode. Slave
Parallel mode is selected by a <011> on the mode pins (M0,
M1, M2).
The agent controlling configuration is not shown. Typically, a
processor, a microcontroller, or CPLD controls the Slave
Parallel interface. The controlling agent provides byte-wide
configuration data, CCLK, a Chip Select (CS) signal and a
Write signal (WRITE). If BUSY is asserted (High) by the
FPGA, the data must be held until BUSY goes Low.
After configuration, the pins of the Slave Parallel port
(D0-D7) can be used as additional user I/O. Alternatively,
the port may be retained to permit high-speed 8-bit read-
back. Then data can be read by deasserting WRITE. If
retention is selected, prohibit the D0-D7 pins from being
used as user I/O. See Readback, page 28.
相关PDF资料 |
PDF描述 |
|---|---|
| XA6SLX100-2FGG484I | IC FPGA SPARTAN 6 484FGGBGA |
| 25LC640T-E/SN | IC EEPROM 64KBIT 2MHZ 8SOIC |
| SST25VF020B-80-4C-SAE-T | IC FLASH SER 2MB 80MHZ SPI 8SOIC |
| XC6SLX100-N3FGG484I | IC FPGA SPARTAN-6 484FPGA |
| SST25LF020A-33-4C-SAE | IC FLASH SER 2MB 33HZ SPI 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XC2S400E-6FGG456I | 制造商:Xilinx 功能描述:FPGA SPARTAN-IIE 400K GATES 10800 CELLS 357MHZ 1.8V 456FBGA - Trays |
| XC2S400E-6FGG676C | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-IIE FPGA |
| XC2S400E-6FGG676I | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-IIE FPGA |
| XC2S400E-6FT256C | 功能描述:IC SPARTAN-IIE FPGA 400K 256FTBG RoHS:是 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:Spartan®-IIE 产品变化通告:Step Intro and Pkg Change 11/March/2008 标准包装:1 系列:Virtex®-5 SXT LAB/CLB数:4080 逻辑元件/单元数:52224 RAM 位总计:4866048 输入/输出数:480 门数:- 电源电压:0.95 V ~ 1.05 V 安装类型:表面贴装 工作温度:-40°C ~ 100°C 封装/外壳:1136-BBGA，FCBGA 供应商设备封装:1136-FCBGA 配用:568-5088-ND - BOARD DEMO DAC1408D750122-1796-ND - EVALUATION PLATFORM VIRTEX-5 |
| XC2S400E-6FT256I | 制造商:Xilinx 功能描述:FPGA SPARTAN-IIE 400K GATES 10800 CELLS 357MHZ 1.8V 256FTBGA - Trays |
发布紧急采购，3分钟左右您将得到回复。