- 您现在的位置：买卖IC网 > PDF目录20664 > ZL2004EVK1 (Intersil)KIT EVAL FOR ZL2004 PDF资料下载
参数资料
| 型号： | ZL2004EVK1 |
| 厂商： | Intersil |
| 文件页数： | 28/42页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR ZL2004 |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
ZL2004
6. Power Management Functional Description
6.1 Input Undervoltage Lockout
The input undervoltage lockout (UVLO) prevents the
ZL2004 from operating when the input falls below a
preset threshold, indicating the input supply is out of
its specified range. The UVLO threshold (V UVLO ) can
be set between 4.5V and 10.8 V using the SS pin. The
simplest implementation is to connect the SS pin as
The UVLO voltage can also be set to any value
between 2.85 V and 16 V via the I 2 C/SMBus interface.
Once an input undervoltage fault condition occurs, the
device can respond in a number of ways as follows:
1. Continue operating without interruption.
2. Continue operating for a given delay period,
followed by shutdown if the fault still exists. The
device will remain in shutdown until instructed to
restart.
3. Initiate an immediate shutdown until the fault has
been cleared. The user can select a specific number
of retry attempts.
The default response from a UVLO fault is an
immediate shutdown of the device. The device will
continuously check for the presence of the fault
condition. If the fault condition is no longer present,
the ZL2004 will be re-enabled.
Please refer to Application Note AN33 for details on
how to configure the UVLO threshold or to select
specific UVLO fault response options via the
I 2 C/SMBus interface.
6.2 Output Overvoltage Protection
The ZL2004 offers an internal output overvoltage
protection circuit that can be used to protect sensitive
load circuitry from being subjected to a voltage higher
than its prescribed limits. A hardware comparator is
used to compare the actual output voltage (seen at the
VSEN pin) to a threshold set to 15% higher than the
target output voltage (the default setting). If the VSEN
voltage exceeds this threshold, the PG pin will de-
assert and the device can then respond in a number of
ways as follows:
1. Initiate an immediate shutdown until the fault has
been cleared. The user can select a specific number
of retry attempts.
28
2. Turn off the high-side MOSFET and turn on the
low-side MOSFET. The low-side MOSFET
remains ON until the device attempts a restart.
The default response from an overvoltage fault is to
immediately shut down. The device will continuously
check for the presence of the fault condition, and when
the fault condition no longer exists the device will be
re-enabled.
For continuous overvoltage protection when operating
from an external clock, the only allowed response is an
immediate shutdown.
Refer to AN33 for details on how to select specific
overvoltage fault response options.
6.3 Output Pre-Bias Protection
An output pre-bias condition exists when an externally
applied voltage is present on a power supply’s output
before the power supply’s control IC is enabled.
Certain applications require that the converter not be
allowed to sink current during start up if a pre-bias
condition exists at the output. The ZL2004 provides
pre-bias protection by sampling the output voltage
prior to initiating an output ramp.
If a pre-bias voltage lower than the target voltage exists
after the pre-configured delay period has expired, the
target voltage is set to match the existing pre-bias
voltage and both drivers are enabled. The output
voltage is then ramped to the final regulation value at
the ramp rate set by the SS pin.
FN6846.3
February 15, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| TTN0.63SV | 5/8" THERMASHIELD TUBE SLV 250' |
| TC1304-ZA0EMF | IC REG DL BUCK/LINEAR SYNC 10DFN |
| ESC10DRTH | CONN EDGECARD 20POS DIP .100 SLD |
| ISL6425EVAL2 | EVAL BOARD 2 FOR ISL6425 |
| ISL59532IK-EVAL | EVAL BOARD FOR ISL59532 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ZL2005 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Digital-DC? Integrated Power Management and Conversion IC |
| ZL2005ALNF | 制造商:Intersil Corporation 功能描述:DIGITAL DC-DC CONTROLLER W/ DRIVERS - TRAY100 - Trays 制造商:Intersil Corporation 功能描述:IC REG CNTRLR BUCK PWM 36-QFN 制造商:Intersil Corporation 功能描述:Digital DC-DC Controller w/ Drivers - BULK 50 |
| ZL2005ALNFT | 功能描述:电压模式 PWM 控制器 DIGTL DC-DC CNTRLR W/DRVRS TR100 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ZL2005ALNFT1 | 功能描述:电压模式 PWM 控制器 DIGTL DC-DC CNTRLR W/DRVRS TR1K RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ZL2005P | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Digital-DC? Controller with Drivers and POLA/DOSA Trim |
发布紧急采购，3分钟左右您将得到回复。