- 您现在的位置：买卖IC网 > PDF目录278507 > ZPSD813F3V-20J 1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52 PDF资料下载
参数资料
| 型号： | ZPSD813F3V-20J |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52 |
| 封装： | PLASTIC, LDCC-52 |
| 文件页数： | 32/132页 |
| 文件大小： | 513K |
| 代理商： | ZPSD813F3V-20J |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页
Preliminary
PSD813F Family
123
Discrepancy – Anytime the MCU changes the state of SDP mode from disabled to
enabled, it must write three command bytes (AAh, 55h, A0h), then write a single dummy
byte to a reserved address space of 128 bytes in length. The dummy byte can be any
pattern. The MCU should not use method 1 or method 2 shown above to enable SDP
mode.
This is only necessary when going from SDP mode disabled to SDP mode enabled.
If SDP mode is already enabled (enabled from the MCU or a stand-alone device
programmer), then the command sequences in Table 9 of the data sheets may be used
to write byte(s) into the EEPROM (no dummy write to reserved space is needed). If the
MCU disables SDP mode, then enables SDP mode again, a dummy write to the
reserved address space is needed to get SDP mode enabled again.
Interim Solution –
Reserve an address range 128 bytes in length within an unused portion of EEPROM.
This 128-byte space can be in any of the four EEPROM segments, and must begin on a
128-byte address boundary.
To enable SDP mode (only after previously being disabled), the MCU must write the
command sequence AAh, 55h, A0h to any valid EEPROM sector at addresses X555h,
XAAAh, X555h respectively. But then it must write a single dummy byte to the first
location within the reserved 128-byte address space. Example (you don’t have to use
these exact addresses or dummy byte value):
AAh >> 8555h
55h >> 8AAAh
A0h >> 8555h
Just like data PSD813F sheet so far.
EEh >> 8080h
Dummy byte EEh is written to reserved address block starting
at 8080h (block is from 8080h to 80FFh).
From this point forward, SDP mode is enabled, until disabled by the MCU or a device
programmer.
If you cannot locate 128 bytes of unused space in your EEPROM memory map, then
you can use populated EEPROM memory. However, you must first read the existing
128 bytes in the reserved space, enable SDP mode with the single dummy write, then
write the original 128 bytes back into the reserved address space.
Temporary
Exceptions to
Specifications
(cont.)
相关PDF资料 |
PDF描述 |
|---|---|
| ZDVG10A | 7 SEG NUMERIC DISPLAY, GREEN, 10.16 mm |
| ZMG75W | SINGLE COLOR LED, GREEN, 2.3 mm |
| ZMGUY62M-01 | DUAL COLOR LED |
| Z505 | INTERCONNECTION DEVICE |
| Z410 | INTERCONNECTION DEVICE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ZPSD813F3V-A-15J | 制造商:WSI 功能描述: |
| ZPSD813F4-12JI | 制造商:WSI 功能描述: |
| ZPSD813F4-15J | 制造商:WSI 功能描述: 制造商:STMicroelectronics 功能描述:microcontroller peripheral devices 制造商:STMicroelectronics 功能描述:Flash in-system programmable microcontroller peripheral device |
| ZPSD813F4-90J | 制造商:WSI 功能描述: |
| ZPSD813F5-15J | 制造商:WSI 功能描述: |
发布紧急采购，3分钟左右您将得到回复。