- 您现在的位置：买卖IC网 > PDF目录278507 > ZPSD813F3V-20J 1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52 PDF资料下载
参数资料
| 型号： | ZPSD813F3V-20J |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52 |
| 封装： | PLASTIC, LDCC-52 |
| 文件页数： | 93/132页 |
| 文件大小： | 513K |
| 代理商： | ZPSD813F3V-20J |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页当前第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页
Preliminary
PSD813F Family
59
The
PSD813F
Functional
Blocks
(cont.)
9.4.2.4 Address In Mode
For microcontrollers that have more than 16 address lines, the higher addresses can be
connected to Port A, B, C, and D. The address input can be latched in the Input Micro
Cell
by the address strobe (ALE/AS). Any input that is included in the DPLD equations for the
PLD’s Flash, EEPROM, or SRAM is considered to be an address input.
9.4.2.5 Data Port Mode
Port A can be used as a data bus port for a microcontroller with a non-multiplexed
address/data bus. The Data Port is connected to the data bus of the microcontroller. The
general I/O functions are disabled in Port A if the port is configured as a Data Port.
9.4.2.6 Peripheral I/O Mode
Peripheral I/O Mode can be used to interface with external peripherals. In this mode, all of
Port A serves as a tri-stateable, bi-directional data buffer for the microcontroller. Peripheral
I/O Mode is enabled by setting Bit 7 of the VM Register to a ‘1’. Figure 26 shows how Port A
acts as a bi-directional buffer for the microcontroller data bus if Peripheral I/O Mode is
enabled. An equation for PSEL0 and/or PSEL1 must be written in PSDabel. The buffer is
tri-stated when PSEL 0 or 1 is not active.
9.4.2.7 JTAG ISP
Port C is JTAG compliant, and can be used for In-System Programming (ISP). You can
multiplex JTAG operations with other functions on Port C because ISP is not performed
during normal system operation. For more information on the JTAG Port, refer to
section 9.6.
9.4.2.3 Address Out Mode
For microcontrollers with a multiplexed address/data bus, Address Out Mode can be used
to drive latched addresses onto the port pins. These port pins can, in turn, drive external
devices. Either the output enable or the corresponding bits of both the Direction Register
and Control Register must be set to a ‘1’ for pins to use Address Out Mode. This must be
done by the MCU at run-time. See Table 22 for the address output pin assignments on
Ports A and B for various MCUs.
For non-multiplexed 8 bit bus mode, address lines A[7:0] are available to Port B in Address
Out Mode.
Note: do not drive address lines with Address Out Mode to an external memory device if it
is intended for the MCU to boot from the external device. The MCU must first boot from
PSD memory so the Direction and Control register bits can be set.
Microcontroller
Port A (3:0)
Port A (7:4)
Port B (3:0)
Port B (7:4)
8051XA (8-Bit)
N/A*
Address (7:4)
Address (11:8)
N/A
80C251
N/A
Address (11:8)
Address (15:12)
(Page Mode)
All Other
Address (3:0)
Address (7:4)
Address (3:0)
Address (7:4)
8-Bit Multiplexed
8-Bit
N/A
Address [3:0]
Address [7:4]
Non-Multiplexed Bus
Table 22. I/O Port Latched Address Output Assignments
N/A = Not Applicable.
相关PDF资料 |
PDF描述 |
|---|---|
| ZDVG10A | 7 SEG NUMERIC DISPLAY, GREEN, 10.16 mm |
| ZMG75W | SINGLE COLOR LED, GREEN, 2.3 mm |
| ZMGUY62M-01 | DUAL COLOR LED |
| Z505 | INTERCONNECTION DEVICE |
| Z410 | INTERCONNECTION DEVICE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ZPSD813F3V-A-15J | 制造商:WSI 功能描述: |
| ZPSD813F4-12JI | 制造商:WSI 功能描述: |
| ZPSD813F4-15J | 制造商:WSI 功能描述: 制造商:STMicroelectronics 功能描述:microcontroller peripheral devices 制造商:STMicroelectronics 功能描述:Flash in-system programmable microcontroller peripheral device |
| ZPSD813F4-90J | 制造商:WSI 功能描述: |
| ZPSD813F5-15J | 制造商:WSI 功能描述: |
发布紧急采购，3分钟左右您将得到回复。