- 您现在的位置：买卖IC网 > PDF目录1888 > 78Q8430-100IGT/F (Maxim Integrated Products)IC LAN MEDIA ACCESS CTLR 100LQFP PDF资料下载
参数资料
| 型号： | 78Q8430-100IGT/F |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 44/88页 |
| 文件大小： | 0K |
| 描述： | IC LAN MEDIA ACCESS CTLR 100LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 90 |
| 控制器类型： | 以太网控制器，MAC/PHY |
| 电源电压： | 3.3V |
| 电流 - 电源： | 230mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-LQFP（14x14） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页
DS_8430_001
78Q8430 Data Sheet
Rev. 1.2
49
6.12 PHY Operations
6.12.1 Automatic MDI/MDIX Cable Crossover Configuration
The transmitter and receiver contain logic and mux to detect and correct for cross over cabling errors.
The implementation is fully compliant with IEEE 802.3 specifications, ensuring interoperation with other
PHYs, which may or may not implement automatic MDI/MDI-X configuration. The automatic MDI/MDI-X
state machine facilitates switching TXN and TXP pins with the RXN and RXP pins, prior to the auto-
negotiation mode of operation. The correct polarization of the crossover circuit is determined by an
algorithm that controls the switching function. Use of an 11-bit Linear Feedback Shift Register (LFSR)
creates a pseudo-random sequence to determine the MDI configuration. Upon making the selection to
either MDI or MDI-X, the 78Q8430 waits for a specified amount of time while evaluating its receive
channel to determine whether the other end of the link is sending link pulses or 10BASE-T or
100BASE-TX data. If link pulses or data are detected, the 78Q8430 remains in that configuration. If link
pulses or data are not detected, it increments it’s LFSR and makes a decision to switch based on the
value of the next bit. The state machine does not move from one state to another while link pulses are
being transmitted.
6.12.2 100Base-TX Transmit
The 78Q8430 PHY contains all of the necessary circuitry to convert the transmit MII signaling from a MAC
to an IEEE-802.3 compliant data-stream driving Cat-5 UTP cabling. The internal PCS interface maps
4-bit nibbles from the MII to 5-bit code groups as defined in Table 24-1 of IEEE-802.3. The 5-bit code
groups are then scrambled and converted to a serial stream before being sent to the MLT-3 pulse
shaping circuitry and line driver. The pulse-shaper uses current modulation to produce the desired output
waveform. Controlled rise/fall time in the MLT-3 signal is achieved using an accurately controlled voltage
ramp generator. The line driver requires an external 1:1 isolation transformer to interface with the line
media. The center-tap of the primary side of the transformer connects to the 3.3 V supply.
6.12.3 100Base-TX Receive
The 78Q8430 PHY receives a 125 MBaud MLT-3 signal through a 1:1 transformer. The signal then goes
through a combination of adaptive offset adjustment (baseline wander correction) and adaptive
equalization. The effect of these circuits is to sense the amount of dispersion and attenuation caused by
the cable and transformer and restore the received pulses to logic levels. The amount of gain and
equalization applied to the pulses varies with the detected attenuation and dispersion and, therefore, with
the length of the cable. The 78Q8430 PHY can compensate for cable loss of up to 10dB at 16 MHz. This
loss is represented as test_chan_5 in Annex A of the ANSI X3.263:1995 specification and corresponds to
approximately 140 m of CAT-5 UTP cabling. The equalized MLT-3 data signal is bi-directionally sliced
and the resulting bit-stream is presented to the CDR where it is re-timed and decoded to NRZ format.
The retimed serial data is converted to parallel, then de-scrambled and aligned into 5 bit code groups.
The receive PCS interface maps these code groups to 4 bit data for the internal MII as outlined in Clause
24 of IEEE-802.3.
6.12.4 10Base-T Transmit
The 78Q8430 PHY takes 4-bit parallel NRZ data via the MII interface and passes it through a parallel to
serial converter. The data is then passed through a Manchester encoder, pre-emphasis pulse-shaper,
media filter and finally to the twisted-pair line driver. The pulse shaper and filter ensures the output
waveforms meet the output voltage template and spectral content requirements detailed in Clause 14 of
IEEE-802.3. Interface to the twisted pair media is through a center-tapped 1:1 transformer. No external
filtering is required. During auto-negotiation and 10BASE-T idle periods, link pulses are transmitted.
The 78Q8430 PHY employs an on board timer to prevent the MAC from capturing a network through
excessively long transmissions. When this timer is exceeded the chip enters the jabber state and
transmission is disabled. The jabber state is exited after the MII goes idle for 500 ms ± 250 ms.
相关PDF资料 |
PDF描述 |
|---|---|
| A1020B-1CQ84C | IC FPGA 2K GATES 84-CQFP COM |
| A1225A-1PQ100C | IC FPGA 2500 GATES 100-PQFP COM |
| A1440A-1VQG100I | IC FPGA 4K GATES 100-VQFP |
| A3P1000-1FGG484T | IC FPGA 1KB FLASH 1M 484-FBGA |
| A3PE1500-PQG208 | IC FPGA 444I/O 208PQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 78Q8430-100IGTR/F | 功能描述:以太网 IC 10/100 Ethernet MAC & PHY RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| 78Q8430-128CGT/F | 制造商:Maxim Integrated Products 功能描述:Ethernet ICs 10/100 Ethernet MAC & PHY |
| 78Q8430-128CGTR/F | 制造商:Maxim Integrated Products 功能描述:Ethernet ICs 10/100 Ethernet MAC & PHY |
| 78Q8430-ARM9-EVM | 功能描述:EVALUATION MODULE 78Q8430 ARM9 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板 |
| 78Q8430EBST#DB | 功能描述:以太网开发工具 3-in-1 Silicon Delay Line RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。