- 您现在的位置：买卖IC网 > PDF目录24812 > 935263912557 (NXP SEMICONDUCTORS) 1 CHANNEL(S), 400M bps, SERIAL COMM CONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | 935263912557 |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 1 CHANNEL(S), 400M bps, SERIAL COMM CONTROLLER, PQFP100 |
| 封装： | 14 X 14 MM, 1 MM HEIGHT, PLASTIC, SOT-386-1, TQFP-100 |
| 文件页数： | 3/56页 |
| 文件大小： | 277K |
| 代理商： | 935263912557 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
Philips Semiconductors
Preliminary specification
PDI1394L21
1394 full duplex AV link layer controller
2000 Jun 06
11
12.3.2
Write accesses
To write to an internal register the host interface must collect the 4 byte values into a 32 bit value and then write the result to the target register
in a single clock tick. This requires a register to hold the 32 bit value being compiled until it is ready to be written to the actual target register.
This temporary register inside the host interface is called the write shadow register. During all write cycles address lines HIF A0 and HIF A1
are used to select which of the 4 bytes of the write shadow register is to be written with the value on the CPU data bus. Only one byte can be
written in a single write access cycle.
UPDATE/COPY CONTROL
HIF A8
HIF A2..7
HIF A0..1
CPU
WRITE
SHADOW
REGISTER
832
32
REGISTERS
TR
Q
MUX
SV00804
NOTES:
1. It is not required to write all 4 bytes of a register: those bytes that are either reserved (undefined) or don’t care do not have to be written in
which case they will be assigned the value that was left in the corresponding byte of the write shadow register from a previous write
access. For example, to acknowledge an interrupt for the isochronous receiver (external address 0x04C), a single byte write to location
0x100+(0x4C)+3 = 0x14F is sufficient. The value 256 represents setting HIF A8=1. The host interface cannot directly access the FIFOs, but
instead reads from/writes into a transfer register (shown as TR in the Figures above). Data is moved between FIFO and TR by internal logic
as soon as possible without CPU intervention.
2. The update control line does not necessarily have to be connected to the CPU address line HIF A8. This input could also be controlled by
other means, for example a combinatorial circuit that activates the update control line whenever a write access is done for byte 3. This
makes the internal updating automatic for quadlet writing.
3. Writing the bytes of the read shadow register can be done in any order and as often as needed (new writes simply overwrite the old value).
12.3.3
Byte order
The bytes in each quadlet are numbered 0..3 from left (most significant) to right (least significant) as shown in Figure 3. To access a register at
internal address N the CPU should use addresses E:
E = N
; to access the upper 8 bits of the register.
E = N + 1
; to access the upper middle 8 bits of the register.
E = N + 2
; to access the lower middle 8 bits of the register.
E = N + 3
; to access the lower 8 bits of the register.
SV00656
29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BYTE 0
BYTE 1
BYTE 3
3130
BYTE 2
Figure 3. Byte order in quadlets as implemented in the host interface
12.3.4
Accessing the packet queues
Although entire incoming packets are stored in the receiver buffer memory they are not randomly accessible. These buffers act like FIFOs and
only the frontmost (oldest) data quadlet entry is accessible for reading. Therefore only one location (register address) is allocated to each of the
two receiver queues. Reading this location returns the head entry of the queue, and at the same time removes it from the queue, making the
next stored data quadlet accessible.
With the current host interface such a read is in fact a move operation of the data quadlet from the queue to the read shadow register. Once the
data is copied into the read shadow register it is no longer available in the queue itself so the CPU should always read all 4 bytes before
attempting any other read access (be careful with interrupt handlers for the PDI1394L21!).
相关PDF资料 |
PDF描述 |
|---|---|
| 935263912551 | 1 CHANNEL(S), 400M bps, SERIAL COMM CONTROLLER, PQFP100 |
| 08-1101-00 | DREHSCHALTER 1POL 12STELLUNGEN |
| 08-1260-00 | ************GESTRICHEN************ |
| 08-1341-00 | DREHSCHALTER 3POL 4STELLUNGEN |
| 08-2101-00 | DREHSCHALTER 2POL 12STELLUNGEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 935264217557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC |
| 935267356112 | 制造商:NXP Semiconductors 功能描述:IC TEA1507PN |
| 935268081112 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC |
| 935268721125 | 制造商:NXP Semiconductors 功能描述:Buffer/Line Driver 1-CH Non-Inverting 3-ST CMOS 5-Pin TSSOP T/R |
| 935269304128 | 制造商:ST-Ericsson 功能描述:IC AUDIO CODEC W/TCH SCRN 48LQFP |
发布紧急采购，3分钟左右您将得到回复。