- 您现在的位置：买卖IC网 > PDF目录10534 > AD9600ABCPZ-105 (Analog Devices Inc)IC ADC 10BIT 105MSPS 64LFCSP PDF资料下载
参数资料
| 型号： | AD9600ABCPZ-105 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 32/72页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 105MSPS 64LFCSP |
| 标准包装： | 1 |
| 位数： | 10 |
| 采样率（每秒）： | 105M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 650mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 64-LFCSP-VQ（9x9） |
| 包装： | 托盘 |
| 输入数目和类型： | 4 个单端，单极；2 个差分，单极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
AD9600
Rev. B | Page 38 of 72
SERIAL PORT INTERFACE (SPI)
The AD9600 SPI allows the user to configure the converter for
specific functions or operations through a structured register
space provided inside the ADC. This may provide the user
with additional flexibility and customization, depending on the
application. Addresses are accessed via the serial port and can
be written to or read from via the port. Memory is organized
into bytes that can be further divided into fields, which are docu-
mented in the Memory Map section. For detailed operational
information, see AN-877 Application Note, Interfacing to High
Speed ADCs via SPI.
CONFIGURATION USING THE SPI
There are three pins that define the SPI: SCLK, SDIO, and CSB
(see Table 19). The SCLK pin is used to synchronize the read
and write data presented from and to the ADC. The SDIO pin is
a dual-purpose pin that allows data to be sent to and read from
the internal ADC memory map registers. The CSB pin is an active-
low control that enables or disables the read and write cycles.
Table 19. Serial Port Interface Pins
Pin
Function
SCLK
Serial Clock. The serial shift clock input, which is used to
synchronize serial interface reads and writes.
SDIO
Serial Data Input/Output. A dual-purpose pin that
typically serves as an input or an output, depending on
the instruction being sent and the relative position in the
timing frame.
CSB
Chip Select Bar. An active-low control that gates the read
and write cycles.
The falling edge of the CSB in conjunction with the rising edge
of the SCLK determines the start of the framing. An example of
the serial timing and its definitions can be found in Figure 72
and Table 5.
Other modes involving the CSB are available. The CSB can be
held low indefinitely, which permanently enables the device;
this is called streaming. The CSB can stall high between bytes to
allow for additional external timing. When CSB is tied high, SPI
functions are placed in high impedance mode. This mode turns
on any secondary functions of the SPI pin.
During an instruction phase, a 16-bit instruction is transmitted.
Data follows the instruction phase, and its length is determined
by the W0 and W1 bits. W0 and W1 represent the number of
data bytes to transfer for either a read or a write. The value
represented by W1:W0 + 1 is the number of bytes to transfer.
All data is composed of 8-bit words. The first bit of the first
byte in a multibyte serial data transfer frame indicates whether
a read command or a write command is issued. This allows the
serial data input/output (SDIO) pin to change direction from an
input to an output.
In addition to word length, the instruction phase determines if
the serial frame is a read or write operation, allowing the serial
port to be used to both program the chip and read the contents
of the on-chip memory. If the instruction is a readback operation,
performing a readback causes the SDIO pin to change direction
from an input to an output at the appropriate point in the
serial frame.
Data can be sent in MSB-first mode or LSB-first mode. MSB-first
mode is the default on power-up and can be changed via the SPI
port configuration register (Address 0x00). For more information
about this and other features, see AN-877 Application Note,
Interfacing to High Speed ADCs via SPI.
HARDWARE INTERFACE
The pins described in Table 19 constitute the physical interface
between the user programming device and the serial port of the
AD9600. The SCLK pin and the CSB pin function as inputs
when using the SPI interface. The SDIO pin is bidirectional,
functioning as an input during write phases and as an output
during readback.
The SPI interface is flexible enough to be controlled by either
FPGAs or microcontrollers. One method for SPI configuration
is described in detail in AN-812 Application Note, Microcontroller-
Based Serial Port Interface (SPI) Boot Circuit.
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK, CSB, and SDIO signals are typically asynchronous to the
ADC clock, noise from these signals can degrade converter
performance. If the on-board SPI bus is used for other devices, it
may be necessary to provide buffers between this bus and the
AD9600 to keep these signals from transitioning at the converter
inputs during critical sampling periods.
Some pins serve a dual function when the SPI interface is not
being used. When the pins are strapped to AVDD or ground
during device power-on, they are associated with a specific
function. The Theory of Operation section describes the
strappable functions supported on the AD9600.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-241-IW-F3 | CONVERTER MOD DC/DC 12V 100W |
| AD7653ACPZ | IC ADC 16BIT UNIPOLAR 48LFCSP |
| VE-241-IW-F2 | CONVERTER MOD DC/DC 12V 100W |
| LTC1279CG | IC A/DCONV SAMPLNG W/SHTDN24SSOP |
| VI-BTN-IV-F4 | CONVERTER MOD DC/DC 18.5V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9600ABCPZ-125 | 功能描述:IC ADC 10BIT 125MSPS 64LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD9600ABCPZ-150 | 功能描述:IC ADC 10BIT 150MSPS 64LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD9600BCPZ-105 | 制造商:Analog Devices 功能描述:ADC Dual Pipelined 105Msps 10-bit Parallel/LVDS 64-Pin LFCSP EP |
| AD9600BCPZ-125 | 制造商:Analog Devices 功能描述:ADC Dual Pipelined 125Msps 10-bit Parallel/LVDS 64-Pin LFCSP EP |
| AD9600BCPZ-150 | 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。