- 您现在的位置：买卖IC网 > PDF目录10534 > AD9600ABCPZ-105 (Analog Devices Inc)IC ADC 10BIT 105MSPS 64LFCSP PDF资料下载
参数资料
| 型号： | AD9600ABCPZ-105 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 42/72页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 105MSPS 64LFCSP |
| 标准包装： | 1 |
| 位数： | 10 |
| 采样率（每秒）： | 105M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 650mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 64-LFCSP-VQ（9x9） |
| 包装： | 托盘 |
| 输入数目和类型： | 4 个单端，单极；2 个差分，单极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页当前第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
AD9600
Rev. B | Page 47 of 72
APPLICATIONS INFORMATION
DESIGN GUIDELINES
When designing the AD9600 into a system, the designer
should, before starting design and layout, become familiar with
these guidelines, which discuss the special circuit connections
and layout requirements for certain pins.
Power and Ground Recommendations
When connecting power to the AD9600, the designer should use
two separate 1.8 V supplies: one supply should be used for AVDD
and DVDD and a separate supply for DRVDD. The AVDD and
DVDD supplies, although derived from the same source, should be
isolated with a ferrite bead or filter choke and have separate
decoupling capacitors. The user can employ several different
decoupling capacitors to cover both high and low frequencies.
These should be located close to the point of entry at the PC
board level and close to the part’s pins with minimal trace
length.
A single PC board ground plane should be sufficient when
using the AD9600. With proper decoupling and smart parti-
tioning of the PC board’s analog, digital, and clock sections,
optimum performance can be easily achieved.
Exposed Paddle Thermal Heat Slug Recommendations
To achieve the best electrical and thermal performance of the
AD9600, the exposed paddle on the underside of the ADC must
be connected to analog ground (AGND). A continuously exposed
(no solder mask) copper plane on the PCB should mate to the
exposed paddle, Pin 0, of the AD9600. In addition, the copper
plane should have several vias to achieve the lowest possible
resistive thermal path for heat dissipation to flow through the
bottom of the PCB, and these vias should be filled or plugged
with nonconductive epoxy.
To maximize the coverage and adhesion between the ADC and
PCB, overlay a silkscreen to partition the continuous plane on
the PCB into several uniform sections. This provides several tie
points between the ADC and PCB during the reflow process.
Using one continuous plane with no partitions guarantees only
one tie point between the ADC and PCB. See the evaluation board
layout. For detailed information on packaging and the PCB layout
of chip scale packages, see the AN-772 Application Note, A Design
and Manufacturing Guide for the Lead Frame Chip Scale Package
(LFCSP).
CML
The CML pin should be decoupled to ground with a 0.1 μF
capacitor, as shown in Figure 47.
RBIAS
The AD9600 requires the user to place a 10 kΩ resistor between
the RBIAS pin and ground. This register sets the master current
reference of the ADC core and should have at least a 1% tolerance.
Reference Decoupling
The VREF pin should be externally decoupled to ground with a
low-ESR 1.0 μF capacitor in parallel with a 0.1 μF ceramic low-
ESR capacitor.
SPI Port
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK, CSB, and SDIO signals are typically asynchronous to the
ADC clock, noise from these signals can degrade the converter’s
performance. If the on-board SPI bus is used for other devices,
it may be necessary to provide buffers between this bus and the
AD9600 in order to keep these signals from transitioning at the
converter inputs during critical sampling periods.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-241-IW-F3 | CONVERTER MOD DC/DC 12V 100W |
| AD7653ACPZ | IC ADC 16BIT UNIPOLAR 48LFCSP |
| VE-241-IW-F2 | CONVERTER MOD DC/DC 12V 100W |
| LTC1279CG | IC A/DCONV SAMPLNG W/SHTDN24SSOP |
| VI-BTN-IV-F4 | CONVERTER MOD DC/DC 18.5V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9600ABCPZ-125 | 功能描述:IC ADC 10BIT 125MSPS 64LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD9600ABCPZ-150 | 功能描述:IC ADC 10BIT 150MSPS 64LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD9600BCPZ-105 | 制造商:Analog Devices 功能描述:ADC Dual Pipelined 105Msps 10-bit Parallel/LVDS 64-Pin LFCSP EP |
| AD9600BCPZ-125 | 制造商:Analog Devices 功能描述:ADC Dual Pipelined 125Msps 10-bit Parallel/LVDS 64-Pin LFCSP EP |
| AD9600BCPZ-150 | 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。