参数资料
| 型号： | ADM1060ARU |
| 厂商： | Analog Devices Inc |
| 文件页数： | 33/52页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVIS/SEQUENC 7-CH 28TSSOP |
| 标准包装： | 50 |
| 系列： | Super Sequencer® |
| 类型： | 序列发生器 |
| 监视电压数目： | 7 |
| 输出： | 可编程 |
| 电压 - 阀值： | 可调节/可选择 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 管件 |
| 配用： | EVAL-ADM1060EBZ-ND - BOARD EVALUATION ADM1060 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
ADM1060
OUTPUTS
PROGRAMMABLE DRIVER OUTPUTS
The ADM1060 has nine programmable driver outputs (PDOs).
These are the logic outputs of the device. Each PDO is normally
controlled by a single PDB. Thus, the PDOs can be set up to
assert when the conditions on the PDB are met, such as when
the SFDs are in tolerance, the levels on the GPI are correct, the
watchdog timer has not timed out, and so on. The PDOs can be
used for a number of functions; for example, to provide a
POWER_GOOD signal when all the SFDs are in tolerance, pro-
vide a reset generator output if one of the SFDs goes out of spec
(which can be used as a status signal for a DSP or other micro-
processor), or provide enable signals for LDOs on the supplies
that the ADM1060 is supervising.
There are a number of pull-up options on the PDOs to enable
the user to program the output level.
The outputs can be programmed as
? Open-drain (allows the user to connect an external pull-up
resistor)
? Open-drain with weak pull-up to V DD
? Push-pull to V DD
? Open-drain with weak pull-up to VPn
? Push-pull to VPn
? Internally charge-pumped high drive (12 V)
The last option is only available on PDO1?4. This allows the
user to directly drive the gate of an N-channel FET in the path
of a power supply. The required pull-up is selected by pro-
gramming Bits 0 to 3 in PnPDOCFG appropriately (see
? The (delayed) output from the associated PLB (enabled by
setting bit CFG4 to 1)
? Data that is driven directly over the SMBus interface (enabled
by setting Bit CFG5 to 1). When set in this mode, the data
from the PDB is disabled and the data on the PDO is the data
on CFG4. Thus, the PDO can be software controlled to initi-
ate a software power-up/power-down.
? An on-chip clock (enabled by setting Bit CFG6 to 1). A
100 kHz clock is available to clock an external device such as
an LED.
More details on these data modes are given in the register map
The default setup of each of the PDOs is to be pulled low by a
weak (20 k?) pull-down resistor. This is also the setup of the
PDOs on power-up until the registers are loaded and the pro-
grammed conditions are latched. The outputs are actively
pulled low once 1 V or greater is seen at any VPn or VH. Until
there is a 1 V supply on the chip, the outputs are high imped-
ance. This provides a known condition for the PDOs during
power-up. The internal pull-down can be overdriven with an
external pull-up of suitable value tied from the PDO pin to the
required pull-up voltage. The 20 kV resistor must be accounted
for in calculating a suitable value. For example, if it is required
to pull PDOn up to 3.3 V, and 5 V is available as an external
supply, the pull-up resistor value is given by:
3.3 V = 5 V × 20 kV /( R UP + 20 kV )
Therefore,
R UP = (100 kV – 66 kV )/3.3 = 10 kV
The data driving each of the PDOs can come from one of three
inputs. These inputs are enabled by a bit each in the
PnPDOCFG registers. The inputs are
The register list and the bit map for the PDOs are shown in
VFET (PDO1–4 ONLY)
V DD
VP4
SEL
10 ?
VP1
20k ?
10 ?
20k ?
10 ?
20k ?
PDB_OUT
CFG4
M_CLK
Figure 23. Programmable Driver Output
Rev. B | Page 33 of 52
20k ?
PDO
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1062ACPZ-REEL7 | IC SEQUENCER/SUPERVISOR 40LFCSP |
| ADM1063ASUZ | IC SUPERVISOR/SEQUENCER 48-TQFP |
| ADM1064ACPZ | IC SEQUENCER/SUPERVISOR 40-LFCSP |
| ADM1065ASUZ | IC SEQUENCER/MONITOR 48-TQFP |
| ADM1066ASUZ-REEL7 | IC SEQUENCER/SUPERVISOR 48TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1060ARUCS0001R7 | 功能描述:IC SUPERVISOR/SEQUENCER 制造商:analog devices inc. 系列:* 零件状态:上次购买时间 标准包装:1 |
| ADM1060ARUCS0100R7 | 功能描述:IC SUPERVISOR/SEQUENCER 制造商:analog devices inc. 系列:* 零件状态:上次购买时间 标准包装:1 |
| ADM1060ARUCS0101R7 | 功能描述:IC SUPERVISOR/SEQUENCER 制造商:analog devices inc. 系列:* 零件状态:上次购买时间 标准包装:1 |
| ADM1060ARUCS0102R7 | 功能描述:IC SUPERVISOR/SEQUENCER 制造商:analog devices inc. 系列:* 零件状态:上次购买时间 标准包装:1 |
| ADM1060ARUCS0103R7 | 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。