- 您现在的位置：买卖IC网 > PDF目录19403 > ADSP-21261SKSTZ150 (Analog Devices Inc)IC DSP 32BIT 150MHZ 144LQFP PDF资料下载
参数资料
| 型号： | ADSP-21261SKSTZ150 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 4/44页 |
| 文件大小： | 0K |
| 描述： | IC DSP 32BIT 150MHZ 144LQFP |
| 产品培训模块： | SHARC Processor Overview |
| 标准包装： | 60 |
| 系列： | SHARC® |
| 类型： | 浮点 |
| 接口： | DAI，SPI |
| 时钟速率： | 150MHz |
| 非易失内存： | ROM（384 kB） |
| 芯片上RAM： | 128kB |
| 电压 - 输入/输出： | 3.30V |
| 电压 - 核心： | 1.20V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 144-LQFP |
| 供应商设备封装： | 144-LQFP（20x20） |
| 包装： | 托盘 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
Rev. 0
|
Page 12 of 44
|
March 2006
ADSP-21261
DAI_P20–1
I/O/T
Three-state with
programmable
pull-up
Digital Applications Interface Pins. These pins provide the physical interface to
the SRU. The SRU configuration registers define the combination of on-chip
peripheral inputs or outputs connected to the pin and to the pin’s output enable.
The configuration registers of these peripherals then determine the exact behavior
of the pin. Any input or output signal present in the SRU may be routed to any of
these pins. The SRU provides the connection from the serial ports, input data port,
precision clock generators, and timers to the DAI_P20–1 pins. These pins have
internal 22.5 k
Ω pull-up resistors which are enabled on reset. These pull-ups can be
disabled in the DAI_PIN_PULLUP register.
SPICLK
I/O
Three-state with
pull-up enabled
Serial Peripheral Interface Clock Signal. Driven by the master, this signal controls
the rate at which data is transferred. The master can transmit data at a variety of
baud rates. SPICLK cycles once for each bit transmitted. SPICLK is a gated clock that
is active during data transfers, only for the length of the transferred word. Slave
devices ignore the serial clock if the slave select input is driven inactive (HIGH).
SPICLK is used to shift out and shift in the data driven on the MISO and MOSI lines.
The data is always shifted out on one clock edge and sampled on the opposite edge
of the clock. Clock polarity and clock phase relative to data are programmable into
the SPICTL control register and define the transfer format. SPICLK has a 22.5 k
Ω
internal pull-up resistor. If SPI master boot mode is selected, MOSI and SPICLK pins
are driven during reset. These pins are not three-stated during reset in SPI master
boot mode.
SPIDS
I
Input only
Serial Peripheral Interface Slave Device Select. An active low signal used to select
the DSP as an SPI slave device. This input signal behaves like a chip select, and is
provided by the master device for the slave devices. In multimaster mode the DSP’s
SPIDS signal can be driven by a slave device to signal to the DSP (as SPI master) that
an error has occurred, as some other device is also trying to be the master device.
If asserted low when the device is in master mode, it is considered a multimaster
error. For a single master, multiple-slave configuration where flag pins are used, this
pin must be tied or pulled high to VDDEXT on the master device. For ADSP-21261 to
ADSP-21261 SPI interaction, any of the master ADSP-21261’s flag pins can be used
to drive the SPIDS signal on the ADSP-21261 SPI slave device.
MOSI
I/O (O/D)
Three-state with
pull-up enabled
SPI Master Out Slave In. If the ADSP-21261 is configured as a master, the MOSI pin
becomes a data transmit (output) pin, transmitting output data. If the ADSP-21261
is configured as a slave, the MOSI pin becomes a data receive (input) pin, receiving
input data. In an ADSP-21261 SPI interconnection, the data is shifted out from the
MOSI output pin of the master and shifted into the MOSI input(s) of the slave(s).
MOSI has a 22.5 k
Ω internal pull-up resistor. If SPI master boot mode is selected,
MOSI and SPICLK pins are driven during reset. These pins are not three-stated during
reset in SPI master boot mode.
MISO
I/O (O/D)
Three-state with
pull-up enabled
SPI Master In Slave Out. If the ADSP-21261 is configured as a master, the MISO pin
becomes a data receive (input) pin, receiving input data. If the ADSP-21261 is
configured as a slave, the MISO pin becomes a data transmit (output) pin, trans-
mitting output data. In an ADSP-21261 SPI interconnection, the data is shifted out
from the MISO output pin of the slave and shifted into the MISO input pin of the
master. MISO has a 22.5 k
Ω internal pull-up resistor. MISO can be configured as O/D
by setting the OPD bit in the SPICTL register.
Note: Only one slave is allowed to transmit data at any given time. To enable broadcast
transmission to multiple SPI slaves, the DSP’s MISO pin may be disabled by setting
(=1) Bit 5 (DMISO) of the SPICTL register.
BOOTCFG1–0
I
Input only
Boot Configuration Select. Selects the boot mode for the DSP. The BOOTCFG pins
must be valid before reset is asserted. See Table 4 on Page 14 for a description of
the boot modes.
Table 2. Pin Function Descriptions (Continued)
Pin
Type
State During and
After Reset
Function
相关PDF资料 |
PDF描述 |
|---|---|
| ADSP-BF531SBBCZ4RL | IC DSP CTLR 16BIT 400MHZ 160-CSP |
| MAX6504UKP005+T | IC TEMP SWITCH SOT23-5 |
| TPSB476K010A0250 | CAP TANT 47UF 10V 10% 1210 |
| TPSB476K006H0500 | CAP TANT 47UF 6.3V 10% 1210 |
| VI-B63-EU-B1 | CONVERTER MOD DC/DC 24V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADSP-21262 | 制造商:AD 制造商全称:Analog Devices 功能描述:SHARC Processor |
| ADSP-21262_05 | 制造商:AD 制造商全称:Analog Devices 功能描述:Embedded Processor |
| ADSP-21262KSTZ200 | 制造商:Analog Devices 功能描述:- Trays |
| ADSP-21262SBBC-150 | 功能描述:IC DSP 32BIT 150MHZ 136-CSPBGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:SHARC® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-21262SBBCZ150 | 功能描述:IC DSP 32BIT 150MHZ 136-CSPBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:SHARC® 标准包装:40 系列:TMS320DM64x, DaVinci™ 类型:定点 接口:I²C，McASP，McBSP 时钟速率:400MHz 非易失内存:外部 芯片上RAM:160kB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:0°C ~ 90°C 安装类型:表面贴装 封装/外壳:548-BBGA，FCBGA 供应商设备封装:548-FCBGA（27x27） 包装:托盘 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
发布紧急采购，3分钟左右您将得到回复。