- 您现在的位置：买卖IC网 > PDF目录19403 > ADSP-21261SKSTZ150 (Analog Devices Inc)IC DSP 32BIT 150MHZ 144LQFP PDF资料下载
参数资料
| 型号： | ADSP-21261SKSTZ150 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 43/44页 |
| 文件大小： | 0K |
| 描述： | IC DSP 32BIT 150MHZ 144LQFP |
| 产品培训模块： | SHARC Processor Overview |
| 标准包装： | 60 |
| 系列： | SHARC® |
| 类型： | 浮点 |
| 接口： | DAI，SPI |
| 时钟速率： | 150MHz |
| 非易失内存： | ROM（384 kB） |
| 芯片上RAM： | 128kB |
| 电压 - 输入/输出： | 3.30V |
| 电压 - 核心： | 1.20V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 144-LQFP |
| 供应商设备封装： | 144-LQFP（20x20） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页当前第43页第44页
Rev. 0
|
Page 8 of 44
|
March 2006
ADSP-21261
DMA transfers are used to move data to and from internal
memory. Access to the core is also facilitated through the paral-
lel port register read/write functions. The RD, WR, and ALE
(address latch enable) pins are the control pins for the
parallel port.
Timers
The ADSP-21261 has a total of four timers: a core timer able to
generate periodic software interrupts, and three general-
purpose timers that can generate periodic interrupts and be
independently set to operate in one of three modes:
Pulse waveform generation mode
Pulse width count/capture mode
External event watchdog mode
The core timer can be configured to use FLAG3 as a timer
expired output signal, and each general-purpose timer has one
bidirectional pin and four registers that implement its mode of
operation: a 6-bit configuration register, a 32-bit count register,
a 32-bit period register, and a 32-bit pulse width register. A sin-
gle control and status register enables or disables all three
general-purpose timers independently.
Program Booting
The internal memory of the ADSP-21261 boots at system
power-up from an 8-bit EPROM via the parallel port, an SPI
master, an SPI slave, or an internal boot. Booting is determined
by the boot configuration (BOOTCFG1–0) pins. Selection of the
boot source is controlled via the SPI as either a master or slave
device, or it can immediately begin executing from ROM.
Phase-Locked Loop
The ADSP-21261 uses an on-chip phase-locked loop (PLL) to
generate the internal clock for the core. On power-up, the
CLKCFG1–0 pins are used to select ratios of 16:1, 8:1, and 3:1.
After booting, numerous other ratios can be selected via soft-
ware control. The ratios are made up of software configurable
numerator values from 1 to 32 and software configurable divi-
sor values of 1, 2, 4, 8, and 16.
Power Supplies
The ADSP-21261 has separate power supply connections for the
internal (VDDINT), external (VDDEXT), and analog (AVDD/AVSS)
power supplies. The internal and analog supplies must meet the
1.2 V requirement. The external supply must meet the 3.3 V
requirement. All external supply pins must be connected to the
same power supply.
Note that the analog supply pin (AVDD) powers the processor’s
internal clock generator PLL. To produce a stable clock, it is rec-
ommended that PCB designs use an external filter circuit for the
AVDD pin. Place the filter components as close as possible to the
mended ferrite chip is the muRata BLM18AG102SN1D). To
reduce noise coupling, the PCB should use a parallel pair of
power and ground planes for VDDINT and GND. Use wide traces
to connect the bypass capacitors to the analog power (AVDD) and
ground (AVSS) pins. Note that the AVDD and AVSS pins specified
in Figure 4 are inputs to the processor and not the analog
ground plane on the board—the AVSS pin should connect
directly to digital ground (GND) at the chip.
TARGET BOARD JTAG EMULATOR CONNECTOR
Analog Devices DSP Tools product line of JTAG emulators uses
the IEEE 1149.1 JTAG test access port of the ADSP-21261 pro-
cessor to monitor and control the target board processor during
emulation. Analog Devices DSP Tools product line of JTAG
emulators provides emulation at full processor speed, allowing
inspection and modification of memory, registers, and proces-
sor stacks. The processor’s JTAG interface ensures that the
emulator will not affect target system loading or timing.
For complete information on Analog Devices’ SHARC DSP
Tools product line of JTAG emulator operation, see the appro-
priate emulator hardware user’s guide.
DEVELOPMENT TOOLS
The ADSP-21261 is supported by a complete set of
CROSSCORE
software and hardware development tools,
including Analog Devices emulators and VisualDSP++
development environment. The same emulator hardware that
supports other SHARC processors also fully emulates the
ADSP-21261.
The VisualDSP++ project management environment lets pro-
grammers develop and debug an application. This environment
includes an easy to use assembler (which is based on an alge-
braic syntax), an archiver (librarian/library builder), a linker, a
loader, a cycle-accurate instruction-level simulator, a C/C++
compiler, and a C/C++ runtime library that includes DSP and
mathematical functions. A key point for these tools is C/C++
code efficiency. The compiler has been developed for efficient
translation of C/C++ code to DSP assembly. The ADSP-21261
SHARC DSP has architectural features that improve the
efficiency of compiled C/C++ code.
The VisualDSP++ debugger has a number of important fea-
tures. Data visualization is enhanced by a plotting package that
offers a significant level of flexibility. This graphical representa-
tion of user data enables the programmer to quickly determine
the performance of an algorithm. As algorithms grow in
Figure 4. Analog Power Filter Circuit
CROSSCORE is a registered trademark of Analog Devices, Inc.
VisualDSP++ is a registered trademark of Analog Devices, Inc.
HI Z FERRITE
BEAD CHIP
LOCATE ALL COMPONENTS
CLOSE TO AVDD AND AVSS PINS
AVDD
AVSS
100nF
10nF
1nF
ADSP-21261
VDDINT
相关PDF资料 |
PDF描述 |
|---|---|
| ADSP-BF531SBBCZ4RL | IC DSP CTLR 16BIT 400MHZ 160-CSP |
| MAX6504UKP005+T | IC TEMP SWITCH SOT23-5 |
| TPSB476K010A0250 | CAP TANT 47UF 10V 10% 1210 |
| TPSB476K006H0500 | CAP TANT 47UF 6.3V 10% 1210 |
| VI-B63-EU-B1 | CONVERTER MOD DC/DC 24V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADSP-21262 | 制造商:AD 制造商全称:Analog Devices 功能描述:SHARC Processor |
| ADSP-21262_05 | 制造商:AD 制造商全称:Analog Devices 功能描述:Embedded Processor |
| ADSP-21262KSTZ200 | 制造商:Analog Devices 功能描述:- Trays |
| ADSP-21262SBBC-150 | 功能描述:IC DSP 32BIT 150MHZ 136-CSPBGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:SHARC® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-21262SBBCZ150 | 功能描述:IC DSP 32BIT 150MHZ 136-CSPBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:SHARC® 标准包装:40 系列:TMS320DM64x, DaVinci™ 类型:定点 接口:I²C，McASP，McBSP 时钟速率:400MHz 非易失内存:外部 芯片上RAM:160kB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:0°C ~ 90°C 安装类型:表面贴装 封装/外壳:548-BBGA，FCBGA 供应商设备封装:548-FCBGA（27x27） 包装:托盘 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
发布紧急采购，3分钟左右您将得到回复。